4130A13 POWER ASSISTED STEERING BOX - R.R. - IF NECESSARY. CHECK WHEEL TOE IN SEPARATELY - INCLUDES. BLEEDING AIR - ON RIGHT HAND DRIVE VERSIONS - Alfa - 166 - eLearn

3314633 - 4130A13 POWER ASSISTED STEERING BOX - R.R. - If necessary. check wheel toe in separately - Includes. bleeding air - on right hand drive versions

) Place the car on a ramp with the wheels perfectly straight.Mark the position of the steering wheel in relation to the upper steering column shroud.Ensure that the ignition key is in the OFF position, then disconnect the negative (-) battery terminal.

	Name	Connector
-	Battery	A1B

Draw off the fluid from the power assisted steering reservoir using a suitable syringe.1. Undo bolts (1a), remove plastic pin (1b) and remove the under-facia lining driver side (1c).

Remove the driver side carpet.1. Undo bolts (1a) and remove the driver side footrest (1b).2. Undo bolts (2a) and remove the central console right side cover (2b)

1. Undo the bolt (1a) and disconnect the steering column (1b) from the power assisted steering box pinion.

The bolt is pretreated and cannot therefore be refitted.

1. Remove retaining ring (1a) and withdraw the fail-safe device (1b) from the steering box pinion.

1. Remove the floor lining, undo the bolts (1a) and remove the power steering box guard (1b) complete with rubber block (1c).

- 7055B54 under-engine guard - r r Guard beneath engine]. - 1084B30 engine oil filter r r - 4450B12 front or rear wheels (two) - r+r - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R. - 1092G10 single engine belt r r - 1092G20 engine component single belt fixed tensioner - one - r + r - 5530A14 alternator - r+r for versions with air conditioner1. Undo the nuts (1a) and disconnect the track rods (1b) from the steering knuckles using the tool (1c).

	Name	Country
1c	Extractor	1.821.169.000

- 1076B52 exhaust pipe (one) leaving l/h or r/h exhaust manifold - r + r1. Undo the nuts (1a) and remove the protective heat shield (1b) from the power steering box.

1. Tighten the bolt on the power steering pipe retaining band.2. Undo the connector (2a) and disconnect the supply pipe from the pump to the power assisted steering box (2b), power assisted steering box side.3. Unscrew the connector (3a) on the return pipe from power steering box to the rigid pipe on the steering box side (3b).

1. Undo the nuts securing the power steering pipes to the steering box.

1. Undo the bolts fixing the power assisted steering box to the front suspension frame.

Release the power steering pipes from the power steering box.1. Remove the power steering box from the right front wheel compartment.

Refitting ( Removing

) 1. Place the power assisted steering box back in its housing and secure it tightening the bolts to the suspension frame to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Nut	POWER STEERING BOX	M12	Front suspension frame side 10.5 - 11.5

Tighten the nuts securing the power steering pipes to the steering box.1. Connect the return pipe from power steering box to rigid pipe (1a) power steering box side and secure by tightening fitting (1b) to the specified torque.

	Fastening	Component	Ø	Value(daNm)
1b	Connector	POWER STEERING/EXCHANGE BOX RUBBER HOSE	M12	(Power steering box side) 3.1 - 3.8

2. Connect the supply pipe from the pump to the power assisted steering box (2a), power assisted steering box side, and tighten the connector (2b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2b	Connector	PIPE BTWN PUMP + POWER STEERING BOX	M14	(Power steering box side) 3.1 - 3.8

3. Tighten the bolt securing the power assisted steering pipes retaining band.

Refit the power steering box heat shield in its seat. - 1076B52 exhaust pipe (one) leaving l/h or r/h exhaust manifold - r + rConnect the steering rods to the front and steering knuckles secure them tightening the nuts to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Nut	ADJUSTABLE STEERING LINKS	M10	(Front wheel hub steering knuckle side) 4.3 ÷ 4.7

- 5530A14 alternator - r+r for versions with air conditioner - 1092G20 engine component single belt fixed tensioner - one - r + r - 1092G10 single engine belt r r - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R. - 4450B12 front or rear wheels (two) - r+r - 1084B30 engine oil filter r r - 7055B54 under-engine guard - r r Guard beneath engine]. Place the power steering box pinion protection complete with rubber block back in its housing and secure with the bolts. Place the failsafe device back in its housing and secure it using a circlip.1. Connect the steering column (1a) to the steering box pinion with a new bolt (1b) and tighten to the specified torque.

Ensure the reference points on the steering wheel and the upper half casing are aligned.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	STEERING SHAFTS	M8	(Power steering box pinion side) 2.8 - 3.2

Place the central console right side protection back in its housing and secure it using the bolt.Place the driver side footrest back in its housing and fix it using the bolts.Put the driver side floor carpet back in place.Place the driver side under-facia lining back in place and fix it using the bolts.Connect the negative (-) battery terminal.Fill the power steering circuit with the recommended fluid.

	Type	Component	Name	Qty.
-	Fluid	POWER ASSISTED STEERING CIRCUIT	TUTELA GI/A	-

Bleed the air from the power steering system as described below.With the front wheels raised off the ground, with the engine switched off turn the steering wheel to full lock, left and right, 4-5 times.Check and, if necessary, top up the fluid level in the reservoir.Remove the vehicle from the ramp.Start the engine and carry out 4 - 5 full steering wheel turn cycles (right and left).Top up the fluid level in the reservoir.