3315350 - 1004E20 engine - dismantle and re-build following operation 1004e10 - wash and check dismantled parts - re-fit cylinder head and oil sump - does not include repairs to cylinder head and auxiliary unit (Automatic transmission)

Dismantling ( Reassembling ) Rotate the engine through 180° on the overhauling stand.1. Remove the manifold for coolant return to the pump.2. Undo the bolts (2a) and remove the knock sensors (2b).

NameConnector
2bDetonation sensor  K50 

NameConnector
2bKnock sensor 2  K51 
3. Undo the bolts (3a) and remove the water pump cover (3b) and bracket (3c).4. Undo the bolts (4a) and remove the water pump drive pulley (4b).
1. Undo the bolts (1a) and remove the water pump (1b).2. Remove the water pump gasket.3. Fit the tool.

NameCountry
3Counter-torque1.820.624.000
4. Undo the nut (4a) and remove the single drive belt (4b).5. Remove the timing drive belt.6. Remove the timing belt drive pulley.
Rotate the engine through 180° on the overhauling stand.1. Undo the bolt fixing the oil pump chain drive to the oil pump.2. Move aside the chain drive from the oil pump using the tool.

NameCountry
2Extractor1.860.954.001
1. Undo the bolts (1a) and remove the complete oil pump (1b).
1. Undo the bolts (1a) and remove the engine block front cover (1b) complete with gasket (1c) and the crankshaft front oil seal (1d).2. Remove the crankshaft key using a suitable drift.
1. Remove the oil pump drive chain.2. Undo the bolt (2a) and remove the connector (2b) for engine oil delivery to the engine block.
1. Undo the bolts (1a) and remove the engine flywheel (1b).2. Remove the tool.

NameCountry
2Counter-torque1.820.624.000
1. Fit the tool.

NameCountry
1Flange1.820.618.000
Turn the crankshaft to gain access to the big end bearing cap bolts on the right bank.2. Undo the nuts (2a) and remove the big end bearing caps (2b) complete with bearing shells (2c) from the right bank.
Rotate the engine through 180° on the overhauling stand.1. Remove the tools from the right bank.

NameCountry
1Liner/bore holder1.820.279.000
2. Remove the cylinder liners (2a), the connecting rod-piston assemblies (2b) and the big end bearings (2c) from the right bank.Separate the connecting rod-piston assemblies from their cylinder liners.Do the same to remove the cylinder liners and connecting rod-piston assemblies for the left bank.Remove the tool.

NameCountry
-Flange1.820.618.000
Rotate the engine through 180° on the overhauling stand.Check that the crankshaft end float is within the recommended values using a magnetic base fitted with a dial gauge.

MeasurementValue
-End float (mm)0.080 - 0.265
1. Undo the nuts (1a) and remove the front and central main bearing caps (1b) using a suitable tool (1c).2. Remove the half-bearings.
1. Undo the nuts (1a) and remove the rear main bearing cap (1b) using the tools (1c) and (1d).

NameCountry
1cLever1.821.006.001

NameCountry
1dExtractor1.821.006.002
2. Remove the rubber seals.3. Remove the half-bearing.
1. Remove the crankshaft.2. Remove the crankshaft rear oil seal.3. Remove the half-bearings.4. Remove the thrust washers.5. Remove the piston cooling oil jets from the engine block.
 - 1028H60  piston, pin set - replace - 1084B18  engine oil pump, removed - check at benchDrill and remove the water/oil sealing plugs from the crankcase to allow washing. Reassembling ( Dismantling ) Wash the dismantled components.Fit the water/oil sealing plugs in the crankcase, using suitable fitting tools.Lubricate all the components for the mechanical couplings using engine oil.Check that the planarity of the cylinder head support surface is within the recommended values; if this is not the case, regrind the cylinder head support surface.

MeasurementValue
-Flatness of cylinder head supporting surface (mm)< 0.1
Measure the cylinder liner diameter and check that it is within the specified values. If this is not the case, replace the cylinder liners/bores.

MeasurementValue
-Inner diameter (mm)Category B87.995 - 88.004
Category C88.005 - 88.014
Classe A87.985 - 87.994
Check that the ovality of the cylinder liners is within the recommended values.

MeasurementValue
-Ovalization (mm)< 0.01
1. Fit the main bearing caps (1a) and tighten the nuts (1b) to torque.

FasteningComponentØValue(daNm)
-NutMAIN BEARING CAPSM12(Engine crankcase side) 2.4 ÷ 2.6 + 77? ÷ 81?
Use the tool for angular tightening of the main bearing cap bolts.

NameCountry
-Protractor1.860.942.000
2. Check that the internal diameter of the main bearings is within the specified values.

MeasurementValue
2Main bearing seat diameter (mm)Category B63.663 ÷ 63.669
Category C63.669 ÷ 63.675
Classe A63.657 ÷ 63.663
Check that the crankshaft lubrication ducts are free from deposits.Check that the diameter of the main journals is within the recommended values; if this is not the case, replace the crankshaft.

MeasurementValue
-Main bearing journal diameter (mm)Category B59.967 ÷ 59.973
Category C59.961 ÷ 59.967
Classe A59.973 ÷ 59.979
Check that the diameter of the crankpins is within the recommended values; if this is not the case, replace the crankshaft.

MeasurementValue
-Crankpin diameter (mm)Category B51.980 ÷ 51.990
Classe A51.990 ÷ 52.000
Check that the inner diameter of the small end bushes is within the recommended limits; if this is not the case, replace the connecting rod.

MeasurementValue
-Inner diameter (mm)20.005 - 20.015
Check that the outer diameter of the gudgeon pins is within the recommended values; if this is not the case, replace the worn gudgeon pins.

MeasurementValue
-Outer diameter (mm)Category B21.997 - 22.000
Classe A21.994 - 21.997
Fit the seals in the cylinder liner/bore and check that the opening between the ends is within the recommended values; if this is not the case, replace the piston seals.

MeasurementValue
-1° sealing ring gap (mm)0.40 - 0.65

MeasurementValue
-2° sealing ring gap (mm)0.40 - 0.65

MeasurementValue
-Scraper ring gap (mm)0.40 - 0.60
Check that the outer diameter of the pistons is within the recommended values. if this is not the case, replace the piston complete with seals and gudgeon pin.

MeasurementValue
-Outer diameter (mm)Category B87.935 - 87.945
Category C87.945 - 87.955
Classe A87.925 - 87.935
Check that the endfloat between compression rings and their seats is within the specified values.

MeasurementValue
-1st° sealing ring end float (mm)0.035 - 0.070

MeasurementValue
-2° sealing ring end float (mm)0.035 - 0.070

MeasurementValue
-Oil scraper ring end float (mm)0.025 - 0.060
1. Fit the caps (1b) on the connecting rods (1a) and fix them tightening the bolts (1c) to torque.

FasteningComponentØValue(daNm)
1cBoltBIG END BEARING CAPSM91.9 ÷ 2.1 + 48? ÷ 52?
Use the tool for angular tightening of the connecting rod cap bolts.

NameCountry
-Protractor1.860.942.000
2. Check that the diameter of the big end is within the recommended values; if this is not the case, replace the connecting rods.

MeasurementValue
-Big end diameter (mm)55.511 - 55.524
 - 1084B18  engine oil pump, removed - check at bench - 1028H60  piston, pin set - replaceCheck that there are no signs of seizing on the flywheel ring gear teeth; if this is not the case, replace it.1. Fit the piston cooling oil jets in the engine block.2. Fit the thrust washers.
The lubrication ducts in the thrust washers are fitted facing the crankshaft shoulder.
3. Fit the main journal half-bearings in the cylinder block/crankcase.4. Fit the crankshaft on the cylinder block/crankcase.5. Fit the main bearing caps (5a) complete with main bearing shells (5b).
The main journal caps are numbered from 1 to 4 starting from the front of the engine.
6. Tighten the main bearing caps to torque.

FasteningComponentØValue(daNm)
6NutMAIN BEARING CAPSM12(Engine crankcase side) 2.4 ÷ 2.6 + 77? ÷ 81?
Use the tool for angular tightening of the main bearing cap bolts.

NameCountry
-Protractor1.860.942.000
1. Fit the crankshaft rear oil seal (1a) using the tool (1b).
The oil seal should be fitted in its housing so that it covers the small openings (1c).

NameCountry
1bFitting tool1.821.150.000
1. Apply the recommended sealant (1a) through the openings (1b) and check that it comes about 5 mm out of the openings (1c)

TypeComponentNameQty.
1aSealantENGINE REAR MOUNT GASKETSLOCTITE 5900-
The oil sump should be fitted within 15 minutes of applying the sealant in the openings for the crankshaft rear support. If this is not the case, remove the edge of the sealant.
Rotate the engine through 180° on the overhauling stand.1. Fit the cylinder liners (1a) complete with compression rings (1b) in the engine block and lock them with tool (1c) tightening the nuts (1d) to torque.

NameCountry
1cLiner/bore holder1.820.279.000
1. Measure the cylinder liner projection from the engine block surface using tool (1a) fitted with a dial gauge (1b) and check that it is within the specified values.

MeasurementValue
1Projection from cylinder block surface (mm)0.01 - 0.06

NameCountry
1aDial gauge mounting1.825.003.000
1. Fit the connecting rod-piston assemblies (1a) complete with bearing shells (1b) in the cylinder liners, using a suitable tool (1c).
The pistons are fitted with the arrow stamped on the crown facing the front of the engine.
Rotate the cylinder block 180° on the overhaul stand.1. Fit the tool.

NameCountry
1Flange1.820.618.000
2. Rotate the crankshaft as appropriate and fit the big end bearing caps (2a) complete with bearing shells (2b) and tighten the bolts (2c) to torque.
The big end bearing caps have the number of the cylinder to which they belong on one side: when refitting, this number should be on the same side as the one on the small end.

FasteningComponentØValue(daNm)
2cBoltBIG END BEARING CAPSM91.9 ÷ 2.1 + 48? ÷ 52?
Use the tool for angular tightening of the connecting rod cap bolts.

NameCountry
-Protractor1.860.942.000
Remove the tool.

NameCountry
-Flange1.820.618.000
Rotate the engine through 180° on the overhauling stand.1. Fit the flywheel and fix it using its bolts, without tightening them.2. Fit the tool.

NameCountry
2Counter-torque1.820.624.000
3. Tighten the flywheel bolts to torque.

FasteningComponentØValue(daNm)
3BoltFLYWHEELM1011.6 ÷ 12.9
Remove the tool.

NameCountry
-Counter-torque1.820.624.000
Rotate the engine through 180° on the overhauling stand.Fit the connector for engine oil delivery to the engine block, and tighten its bolt.Fit the oil pump drive chain.Fit the crankshaft key.Fit the engine block front cover complete with gasket and fix it using the bolts.Fit the complete oil pump and fix it using the bolts.Tighten the bolt on the oil pump chain drive to torque.

FasteningComponentØValue(daNm)
-BoltENGINE OIL PUMP DRIVE CHAINM147.9 - 9.7
1. Fit the crankshaft front oil seal (1a) using the tool (1b).

NameCountry
1bFitting tool1.860.949.000
Apply the recommended sealant to the entire perimeter of the crankcase sump.

TypeComponentNameQty.
-SealantOIL SUMPLOCTITE 5900-
Fit the crankcase sump.Tighten the sump bolts to torque.

FasteningComponentØValue(daNm)
-BoltOIL SUMPM71.3 ÷ 1.6
Fit the water pump complete with gasket and fix it to the engine block, tightening the bolts to torque.

FasteningComponentØValue(daNm)
-BoltCOOLANT PUMPM60.7 - 0.9
Fit the water pump cover and its bracket, and fix it using the bolts.Fit the knock sensors and fix them using their bolts.Fit the manifold for coolant return to the pump.Rotate the crankshaft until the piston of cylinder no. 1 is at T.D.C.1. Before fitting the cylinder head, rotate the camshafts using the tools (1a) until the reference marks (1b) on the shafts line up with the cylinder head top surface.

NameCountry
1aCounter-torque1.822.146.000
Remove the tool.

NameCountry
-Liner/bore holder1.820.279.000
Fit the cylinder head centring bushes to the engine block.Fit the new cylinder head gaskets.
The cylinder head gaskets are of the Astadur type.The material from which they are made undergoes polymerization during engine operation, so they harden considerably during use.In order for the polymerization process to take place it is necessary to:keep the gasket in its sealed container until fittingnot lubricate or get oil on the gasket and the contact surfaces.
Position the cylinder heads on the engine block.1. Tighten the nuts of the cylinder heads (1a) to torque using the tool (1b) for angle tightening.Follow the order shown in the diagram for each tightening sequence.The diagram shows the right cylinder head; the tightening order for the left cylinder head is symmetrical;

FasteningComponentØValue(daNm)
1aNutCYLINDER HEADM122.4 ÷ 2.6 + 240?

NameCountry
1bProtractor1.860.942.000
1. Remove the camshaft caps 4 and 7 from the left cylinder head.2. Remove the camshaft caps B and G from the right cylinder head.
1. Fit the tool in place of the removed camshaft caps.

NameCountry
1Gauge1.825.040.000
Slacken the bolts on the camshaft drive pullies using the tool as counter-torque.

NameCountry
-Counter-torque1.822.146.000
Fit the timing belt drive pulley.Fit the fixed single drive belt tensioner and fix it with its bolt.Fit the alternator mounting and fix it using the bolts.Fit the alternator rear bracket and fix it with its bolts.1. Fit the tool (1a), complete with dial gauge (1b), in the housing of the spark plug for cylinder no. 1.

NameCountry
1aExtension1.825.013.000
Rotate the crankshaft, using small movements (in both directions), until the piston for cylinder no. 1 is at T.D.C. at the power stroke.
Make sure that the last crankshaft rotation is in the direction of operation.
1. Fit the timing belt starting from the drive pulley and continuing in an anti-clockwise direction, making sure that the drive sections are firmly taut.
1. Fit the tool (1a) and secure it with the alternator bolt (1b) and the bolt (1c) to the water pump.
The bolt (1b) should be shimmed with a suitable spacer to recover the thickness of the alternator. The tool lug (1d) must press against the moving part of the timing belt tensioner.

NameCountry
1aBelt tensioner1.860.950.000
2. Adjust the nut (2a) of the belt tensioner tool until the moving reference on the belt tensioner (2b) is under the fixed reference.
1. Tighten the bolts (1a) for the camshaft pullies to torque using the tools (1b) for counter-torque.

FasteningComponentØValue(daNm)
1aBoltTIMING GEAR DRIVEN PULLEYSM106.8 ÷ 8.4

NameCountry
1bCounter-torque1.822.146.000
Remove the tool.

NameCountry
-Gauge1.825.040.000
Fit the camshaft caps in place of the removed tool and fix them, tightening the bolts to torque.

FasteningComponentØValue(daNm)
-BoltCAMSHAFT CAPSM81.8 - 2.0
Rotate the crankshaft through two revolutions in its direction of rotation to allow the timing belt to bed in.1. Check that the moving reference on the timing belt tensioner lines up with the fixed reference.2. If the references do not line up, slightly discharge the tensioner acting on the tensioning tool nut and make sure that the references are aligned.3. Tighten the timing belt tensioner bolts to torque.

FasteningComponentØValue(daNm)
3BoltMOBILE TIMING TENSIONERM81.7 ÷ 2.1
Remove the tool.

NameCountry
-Belt tensioner1.860.950.000
1. Fit the tool.

NameCountry
1Counter-torque1.820.624.000
2. Fit the single belt drive pulley (2a) and tighten the nut (2b) to torque.

FasteningComponentØValue(daNm)
2bNutCRANKSHAFT PULLEYM2820.0 - 24.7
Remove the tool.

NameCountry
-Counter-torque1.820.624.000
Fit the water pump drive pulley and fix it using the bolts.Fit the oil filter mounting and intermediate shaft complete with seal and fix it with the bolts.Fit the water-oil heat exchanger complete with pipes.Fit the oil filter.Fit the single belt automatic tensioner.Fit the power unit rigid support, timing gear side, and fix it using the bolts.Fit the air conditioner compressor and fix it with its bolts.Fit the tappet covers and fix them with their bolts.Fit the exhaust manifolds and fix them using the nuts.Fit the left exhaust manifold shield and fix it using the nuts.Fit the oil level dipstick and fix it using the bottom nut and top bolt.Fit the thermostat and fix it using the bolts.Connect, to the thermostat, the coolant supply pipe to the water-oil heat exchanger.Fit the ignition coils and fix them using the bolts.Fit the bracket securing the timing cover and fix it using the bolts.Connect the flexible pipe to the fuel distribution manifold rigid pipe.Tighten the bolt joining the timing belt rear covers.Fit the timing belt covers and fix them using the bolts.Fit the single drive belt.Push the single belt tensioner with a spanner to remove the belt tensioner retaining pin.Place the electrical wiring back in its housing and fix it to the bands.Connect the electrical connections to the ignition coils.Connect the electrical connections to the injectors. Fit the electrical wiring securing brackets to the rocker covers and fix them using the bolts.Connect the electrical connection for the knock sensor.Connect the electrical connection for the air conditioning compressor.Fit the left cylinder head ignition coils cover and fix it using the bolts.Connect the earth lead to the left cylinder head tappet cover.Connect the electrical connection to the engine coolant temperature sensor.Connect the electrical connection for the rear knock sensor (black).Connect the electrical connection for the knock sensor (black).Connect the electrical connection for the timing sensor (light blue).Fit the complete intake chamber and fix it using the bolts.Tighten the bands fixing the air intake ducts to the intake chamber.Connect the condensation oil return pipe to the separator.Connect the oil vapour recovery pipe.Connect the electrical connection of the throttle body.Connect the earth lead on the left cylinder head rocker cover. - 1004D40  engine - position on stand and remove