1008A44 REAR RIGID MOUNT - R R (AUTOMATIC TRANSMISSION) - Alfa - 166 - eLearn

3314035 - 1008A44 rear rigid mount - r r (Automatic transmission)

) Position the vehicle on the ramp. Make sure that the ignition is OFF (STOP position), then disconnect the negative battery terminal (refer to op. 5530B10 battery - r+r ).

	Name	Connector
-	Battery	A1B

- 7040D12 engine front side cover (one) lh or rh - r r (right and left) - 7040D30 engine bay front beam cover - r r . - 7040D14 engine bay rear side cover (one) lh or rh - r r (right and left) - 7055B39 front additional wheel arch half (one), lh or rh, front element - r r . - 7055A43 central front grille - r r . - 7055A41 RIGHT FRONT GRILLE - R.R. . - 7055B10 Front BUMPER - R.R. . 1. Disconnect the oil vapour recovery pipe from the separator.2. Disconnect the oil vapour recirculation pipe from the separator.3. Undo the bolts (3a) and remove the oil vapour separtor (3b) away from the cylinder head.

1. Fit the engine mounting bracket (1a) on the right cylinder head and fix it using the bolt (1b).2. Fit the engine mounting bracket (2a) on the left cylinder head and fix it using the bolt (2b).

Undo the bolt and remove the front bumper mounting bracket to allow the power unit supporting tools to be correctly positioned.1. Fit the safety tools (1a), (1b) and (1c) for supporting the power unit.

	Name	Country
1a	Support mountings	1.870.650.000

	Name	Country
1b	Crossmember	1.820.581.000

	Name	Country
1c	Mount	1.820.226.000

2. Connect the rods for the tools to the mounting brackets fitted previously and tension them.

- 4450B10 Front WHEEL (one) - R.R. (left). - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R. (right) - 7055B54 under-engine guard - r r . 1. Remove the engine oil filter (1a) using a suitable tool (1b).

Recover the engine oil in a suitable container.

- 1076B52 exhaust pipe (one) leaving l/h or r/h exhaust manifold - r + r (right and left) - 2710A31 intermediate drive shaft - r r . - 1092G10 single engine belt r r . - 1092G20 engine component single belt fixed tensioner - one - r + r . 1. Disconnect the electrical connection for the insufficient engine oil pressure switch.

	Name	Connector
1	Insufficient engine oil pressure (switch) sensor	K30

2. Undo and remove the insufficient engine oil pressure switch.

1. Disconnect the electrical connections (1a) and (1b) from the alternator.

	Name	Connector
1a	Alternator	A10A

	Name	Connector
1b	Alternator	A10B

2. Undo the bolts (2a) and remove the alternator (2b).

1. Undo the bolt (1a) and the nut (1b) and remove the brackets (1c) supporting the cooling radiator engine oil supply and return pipes.2. Undo the connectors (2a) and disconnect the cooling radiator engine oil supply and return pipes (2b).

Release the electrical wiring from the band on the starter motor rear mounting bracket.1. Undo the nuts (1a) and remove the starter motor rear mounting bracket (1b).2. Undo the bolts (2a) and the nuts (2b) fixing the rigid rear support for the power unit to the cylinder block/crankcase.

1. Undo the bolts (1a) and remove the alternator mounting (1b).

1. Undo the nut fixing the rear power unit rigid support to the flexible mounting.

- 1008C10 power unit upper reaction link r r . - 1008C16 body link bracket - r r . 1. Undo the nut fixing the timing side rigid engine support to the flexible mounting.

1. Loosen the two bolts fixing the gearbox side support flexible mounting to the front suspension frame.

1. Raise the power unit, as necessary, using the rods for the supporting tools and remove the power unit rigid rear support.

Refitting ( Removing

) Place the rigid rear support for the power unit back in its housing.Place the power unit back in its housing using the supporting tools.1. Tighten the bolts fixing the gearbox side support flexible mounting to the front suspension frame to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	GEARBOX SIDE RUBBER MOUNT	M8	(Front suspension frame side) 2.4 - 2.9

1. Tighten the nut fixing the timing side rigid engine support to the flexible mounting to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Nut	ENGINE MOUNT TIMING SIDE	M10	(Flexible mounting side) 3.8 - 4.7

- 1008C16 body link bracket - r r . - 1008C10 power unit upper reaction link r r . 1. Tighten the nut securing the rear power unit rigid support to the flexible mounting to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Nut	POWER UNIT RIGID REAR MOUNT	M10	(Flexible mounting side) 3.8 - 4.7

Fit the alternator mounting and fix it using the bolts.1. Tighten the bolts (1a) and the nuts (1b) fixing the power unit rigid rear support to the cylinder block to the specified torque.

	Fastening	Component	Ø	Value(daNm)
1a	Bolt	POWER UNIT RIGID REAR MOUNT	M8	(Engine crankcase side) 1.9 - 2.3

	Fastening	Component	Ø	Value(daNm)
1b	Nut	POWER UNIT RIGID REAR MOUNT	M8	(Engine crankcase side) 1.9 - 2.3

2. Fit the starter motor rear mounting bracket (2a) and fix it using the nuts (2b).Fix the electrical wiring to the band on the starter motor rear mounting bracket.

Connect the cooling radiator engine oil supply and return pipes and fix them tightnening the connectors to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Connector	PIPE DELIVERING OIL TO RADIATOR	-	Rigid rear. power unit support side -

	Fastening	Component	Ø	Value(daNm)
-	Connector	OIL RETURN PIPE FROM RADIATOR	-	Rigid rear. power unit support side -

Fit the cooling radiator engine oil supply and return pipes and fix them using the bolt and the nut.1. Fit the alternator (1a) and fix it tightening the bolts (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	ALTERNATOR ASSEMBLY	M8	(Mounting bracket side) 1.9 ÷ 2.3

1. Connect the electrical connections (1a) and (1b), checking that there is no contact with the terminal for the B+ cable (1c) and the pin for the D+ cable (1d).

	Name	Connector
1a	Alternator	A10A

	Name	Connector
1b	Alternator	A10B

2. Secure the cables using the nuts.

Take special care to ensure that the alternator cables are correctly positioned in their housings, following the routing illustrated exactly.

Fit the insufficient engine oil pressure switch and tighten it to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	-	OIL PRESSURE W/L	M14	Rigid power unit rear. support side. -

Connect the electrical connection for the insufficient engine oil pressure switch. - 1092G20 engine component single belt fixed tensioner - one - r + r . - 1092G10 single engine belt r r . - 2710A31 intermediate drive shaft - r r . - 1076B52 exhaust pipe (one) leaving l/h or r/h exhaust manifold - r + r (right and left) Fit the engine oil filter and tighten it fully by hand. - 7055B54 under-engine guard - r r . - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R. (right) - 4450B10 Front WHEEL (one) - R.R. (left). Remove the safety tools used for supporting the power unit.

	Name	Country
-	Support mountings	1.870.650.000

	Name	Country
-	Crossmember	1.820.581.000

	Name	Country
-	Mount	1.820.226.000

Fit the front bumper mounting bracket and fix it using the bolt.Undo the bolts and remove the engine mounting brackets from the cylinder heads.Place the oil vapour separator back in its housing and fix it using the bolts.Connect the oil vapoer recirculation pipe to the separator.Connect the oil vapour recovery pipe to the separator. - 7055B10 Front BUMPER - R.R. . - 7055A41 RIGHT FRONT GRILLE - R.R. . - 7055A43 central front grille - r r . - 7055B39 front additional wheel arch half (one), lh or rh, front element - r r . - 7040D14 engine bay rear side cover (one) lh or rh - r r (right and left) - 7040D30 engine bay front beam cover - r r . - 7040D12 engine front side cover (one) lh or rh - r r (right and left) Top up the engine oil lubrication circuit using the recommended oil.

	Type	Component	Name	Qty.
-	Oil	ENGINE LUBRICATION CIRCUIT	SELENIA 20K	-

Connect the battery terminal (-).Remove the car from the ramp.