3314039 - 1008B20 power unit intermediate mount flexible block - replace (Automatic transmission)

Removing ( Refitting ) Position the vehicle on the ramp. Make sure that the ignition is OFF (STOP position), then disconnect the negative battery terminal (refer to op.   5530B10  battery - r+r ).

	Name	Connector
-	Battery	A1B

 - 7040D12  engine front side cover (one) lh or rh - r r (right and left)  - 7040D30  engine bay front beam cover - r r .  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right and left)  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r .  - 7055A43  central front grille - r r .  - 7055A41  RIGHT FRONT GRILLE - R.R. .  - 7055B10  Front BUMPER - R.R. . 1. Disconnect the oil vapour recovery pipe from the separator.2. Disconnect the oil vapour recirculation pipe from the separator.3. Undo the bolts (3a) and remove the oil vapour separtor (3b) away from the cylinder head. 1. Fit the engine mounting bracket (1a) on the right cylinder head and fix it using the bolt (1b).2. Fit the engine mounting bracket (2a) on the left cylinder head and fix it using the bolt (2b). Undo the bolt and remove the front bumper mounting bracket to allow the power unit supporting tools to be correctly positioned.1. Fit the safety tools (1a), (1b) and (1c) for supporting the power unit.

	Name	Country
1a	Support mountings	1.870.650.000

	Name	Country
1b	Crossmember	1.820.581.000

	Name	Country
1c	Mount	1.820.226.000

2. Connect the rods for the tools to the mounting brackets fitted previously and tension them.  - 4450B10  Front WHEEL (one) - R.R. (left).  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. (right)  - 7055B54  under-engine guard - r r .  - 1076B52  exhaust pipe (one) leaving l/h or r/h exhaust manifold - r + r (right and left) 1. Undo the bolts (1a) and disconnect the right front half shaft (1b) from the intermediate half shaft.

The above bolts have been treated with an eslok type material therefore they should be replaced each time they are removed.

Remove the clip and release the right front brake caliper flexible pipe from the mounting bracket.1. Undo the nut (1a) and disconnect the upper track control arm (1b) from the front hub steering knuckle using tool (1c).

	Name	Country
1c	Extractor	1.821.169.000

Move the right front driveshaft away from the intermediate driveshaft. 1. Undo the nut fixing the rear power unit rigid support to the flexible mounting. 1. Undo the nut fixing the timing side rigid engine support to the flexible mounting. 1. Loosen the two bolts fixing the gearbox side support flexible mounting to the front suspension frame.  - 1008C10  power unit upper reaction link r r .  - 1008C16  body link bracket - r r . Raise the power unit, as necessary, using the supporting tool rods.1. Undo the bolts (1a) and remove the flexible mounting for the power unit rear support (1b). Refitting ( Removing ) 1. Fit the flexible mounting for the power unit rear support (1a) and fix it tightening the bolts (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	INTERM RUBBER MOUNT	M10	(Front suspension frame side) 4.9 - 6.1

Place the power unit back in its housing using the supporting tools. - 1008C16  body link bracket - r r .  - 1008C10  power unit upper reaction link r r . 1. Tighten the bolts fixing the gearbox side support flexible mounting to the front suspension frame to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	GEARBOX SIDE RUBBER MOUNT	M8	(Front suspension frame side) 2.4 - 2.9

1. Tighten the nut fixing the timing side rigid engine support to the flexible mounting to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Nut	ENGINE MOUNT TIMING SIDE	M10	(Flexible mounting side) 3.8 - 4.7

1. Tighten the nut securing the rear power unit rigid support to the flexible mounting to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Nut	POWER UNIT RIGID REAR MOUNT	M10	(Flexible mounting side) 3.8 - 4.7

Place the right driveshaft back in its housing.Connect the upper track control arm to the front hub steering knuckle and fix it tightening the nut to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Nut	FRONT SUSPENSION TOP LEVER	M10	Front hub steering knuckle side 4.3 - 4.7

Fix the right front brake caliper flexible pipe to the mounting bracket and fix it using the clip.1. Connect the right front driveshaft (1a) to the intermediate driveshaft and fix it tightening the bolts (1b) to the recommended torque.

The above bolts have been treated with an eslok type material therefore they should be replaced each time they are removed.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	FRONT DRIVE SHAFT COMPLETE WITH JOINTS	M10	(Intermediate driveshaft side) 5.2 - 5.8

 - 1076B52  exhaust pipe (one) leaving l/h or r/h exhaust manifold - r + r (right and left)  - 7055B54  under-engine guard - r r .  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. (right)  - 4450B10  Front WHEEL (one) - R.R. (left). Remove the safety tools used for supporting the power unit.

	Name	Country
-	Support mountings	1.870.650.000

	Name	Country
-	Crossmember	1.820.581.000

	Name	Country
-	Mount	1.820.226.000

Fit the front bumper mounting bracket and fix it using the bolt.Undo the bolts and remove the engine mounting brackets from the cylinder heads.Place the oil vapour separator back in its housing and fix it using the bolts.Connect the oil vapoer recirculation pipe to the separator.Connect the oil vapour recovery pipe to the separator. - 7055B10  Front BUMPER - R.R. .  - 7055A41  RIGHT FRONT GRILLE - R.R. .  - 7055A43  central front grille - r r .  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r .  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right and left)  - 7040D30  engine bay front beam cover - r r .  - 7040D12  engine front side cover (one) lh or rh - r r (right and left) Connect the battery terminal (-).Remove the car from the ramp.