3314100 - 1040A70 submerged pump assembly complete with level guage control - r + r (Automatic transmission)

When scrapping the submerged pump assembly with level gauge mechanism, always empty of fuel as follows:

  • while removing the submerged pump assembly, draw off any fuel in the tank using an in-line pump (electric or manual);
  • fully remove the submerged pump assembly then, working at the bench, connect an in-line pump (electric or manual) to the assembly connector;
  • run the pump for as long enough to collect most of the petrol present inside the filter.

When scrapping the submerged pump assembly with level gauge mechanism, always empty of fuel as follows:

  • while removing the submerged pump assembly, draw off any fuel in the tank using an in-line pump (electric or manual);
  • fully remove the submerged pump assembly then, working at the bench, connect an in-line pump (electric or manual) to the assembly connector;
  • run the pump for as long enough to collect most of the petrol present inside the filter.

When scrapping the submerged pump assembly with level gauge mechanism, always empty of fuel as follows:

  • while removing the submerged pump assembly, draw off any fuel in the tank using an in-line pump (electric or manual);
  • fully remove the submerged pump assembly then, working at the bench, connect an in-line pump (electric or manual) to the assembly connector;
  • run the pump for as long enough to collect most of the petrol present inside the filter.
Removing ( Refitting ) Position the vehicle on the ramp. Make sure that the ignition is off (STOP position), then disconnect the negative battery terminal (refer to op.   5530B10  battery - r+r ).

NameConnector
-Battery  A1B 
Discharge the fuel supply pressure (  See assembly 10   ENGINE ).  - 7040B10  load platform (luggage platform) trim - r+r . 1. Undo the bolts (1a) and remove the access cover (1b) to the immersed pump assembly complete with gauge.2. Disconnect the electrical connection from the immersed pump assembly complete with gauge.

NameConnector
2Fuel pump and sender unit  N40 
3. Disconnect the rapid attachment for the fuel supply pipe.
1. Undo the right nut (1a) fixing the immersed pump assembly complete with gauge using the tool (1b).

NameCountry
1bKey1.821.167.000
2. Remove the immersed pump assembly complete with gauge.
Refitting ( Removing ) Fit the immersed pump assembly complete with gauge so that the arrow stamped on the cover is in line with the one on the tank.Fit the ring nut fixing the immersed pump assembly complete with gauge and tighten it using the tool.

NameCountry
1bKey1.821.167.000
Connect the rapid attachment for the fuel supply pipe.Connect the electrical connection to the immersed pump assembly complete with gauge.Fit the access cover and fix it using the bolts. - 7040B10  load platform (luggage platform) trim - r+r . Connect the negative (-) battery terminal.Remove the car from the ramps.

When scrapping the submerged pump assembly with level gauge mechanism, always empty of fuel as follows:

  • while removing the submerged pump assembly, draw off any fuel in the tank using an in-line pump (electric or manual);
  • fully remove the submerged pump assembly then, working at the bench, connect an in-line pump (electric or manual) to the assembly connector;
  • run the pump for as long enough to collect most of the petrol present inside the filter.
Removing ( Refitting ) Position the vehicle on the ramp. Ensure that the ignition key is in stop position, then disconnect the battery negative terminal (  - 5530B10  battery - r+r ).

NameConnector
-Battery  A1B 
Discharge the fuel supply pressure (  See assembly 10   ENGINE ). Proceed with removal  - 7040B10  load platform (luggage platform) trim - r+r . 1. Undo the bolts (1a) and remove the access cover (1b) to the immersed pump assembly complete with gauge.2. Disconnect the electrical connection from the immersed pump assembly complete with gauge.

NameConnector
2Fuel pump and sender unit  N40 
3. Disconnect the rapid attachment for the fuel supply pipe.
1. Undo the right nut (1a) fixing the immersed pump assembly complete with gauge using the tool (1b).

NameCountry
1bKey1.870.736.000
2. Remove the immersed pump assembly complete with gauge.Remove the O-ring.
Refitting ( Removing ) 1. Refit the O-Ring in its seat on the fuel tank collar and ensure it is correctly positioned.
Fit the immersed pump assembly complete with gauge so that the arrow stamped on the cover is in line with the one on the tank.Fit the ring nut fixing the immersed pump assembly complete with gauge and tighten it using the tool.

NameCountry
-Key1.870.736.000
Connect the rapid attachment for the fuel supply pipe.Connect the electrical connection to the immersed pump assembly complete with gauge.Fit the access cover and fix it using the bolts. Proceed with the removal  - 7040B10  load platform (luggage platform) trim - r+r . Connect the negative (-) battery terminal.Remove the car from the ramps.