2130C36 OIL SEAL FOR LH DIFFERENTIAL SHAFT - R R (AUTOMATIC TRANSMISSION) - Alfa - 166 - eLearn

3314515 - 2130C36 oil seal for lh differential shaft - r r (Automatic transmission)

) Position the vehicle on the ramp. Make sure that the ignition is OFF (STOP position), then disconnect the negative battery terminal (refer to op. 5530B10 battery - r+r ).

	Name	Connector
-	Battery	A1

- 4450B10 Front WHEEL (one) - R.R. (left).. - 7055B39 front additional wheel arch half (one), lh or rh, front element - r r (left). - 7055B54 under-engine guard - r r . 1. Undo the bolts (1a) and disconnect the front left half shaft (1b) from the differential inner shaft.

The above bolts are treated with eslok anti-slackening material and must therefore be replaced whenever they are removed.

1. Remove the retainer (1a) and release the front right brake caliper flexible hose (1b) from its mounting bracket.2. Release the brake pad wear sensor cable (2a) and the front right wheel speed sensor cable (2b) from their mounting brackets.

1. Undo the bolt securing the anti-roll bar joint mounting bracket to the front shock absorber fork.2. Undo the bolt fixing the front shock absorber fork to the track control arm, shock absorber stem side.3. Undo the bolt fixing the front shock absorber fork to the track control arm, track control arm side.

Position a hydraulic jack under the hub steering knuckle.1. Undo the nut (1a) and disconnect the upper track control arm (1b) from the front hub steering knuckle using tool (1c).

	Name	Country
1c	Extractor	1.821.169.000

1. Lower the hydraulic jack and remove the front shock absorber fork with track control arm.Move the steering knuckle/drive shaft assembly from the differential inner shaft.

1. Remove the automatic transmission differential inner half shaft (1a) using the tools (1b) and (1c).

Collect the automatic transmission fluid which leaks out into a suitable container.

	Name	Country
1b	Counter weight	1.821.161.000

	Name	Country
1c	Flange	1.820.229.000

1. Remove the differential shaft oil seal.

Refitting ( Removing

) 1. Fit the differential shaft oil seal (1a) using the tools (1b) and (1c).

	Name	Country
1b	Fitting tool	1.821.202.000

	Name	Country
1c	Fitting tool	1.821.201.000

Refit the automatic transmission differential inner half shaft in its seating.Replace the front shock absorber fork with track control arm in its housing.Raise the hydraulic jack placed under the steering knuckle.1. Connect the upper track control arm (1a) to the front steering knuckle and fix it tightening the nut (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Nut	FRONT SUSPENSION TOP LEVER	M10	Front hub steering knuckle side 4.3 - 4.7

Remove the hydraulic jack from under the hub steering knuckle.1. Tighten the bolt fixing the front shock absorber fork to the track control arm, track control arm side to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	FRONT DAMPER FORK ON WISHBONE	M12	Lower track control arm side 8.6 - 9.6

2. Tighten the bolt securign the front shock absorber fork to the track control arm, shock absorber stem side.

	Fastening	Component	Ø	Value(daNm)
2	Bolt	FRONT DAMPER FORK ON WISHBONE	M12	Shock absorber side 11.7 - 12.9

3. Tighten the bolt securing the anti-roll bar joint mounting bracket to the front shock absorber fork.

Firx the brake pad wear sensor cable and the front right wheel speed sensor cable to their mounting brackets.Fix the front right brake caliper flexible hose to its mounting bracket and fit the retainer.1. Connect the front left half shaft (1a) to the differential inner shaft and tighten its bolts (1b) to the specified torque.

Fit the service tank protection on the left side and secure it with its bolt.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	FRONT DRIVE SHAFT COMPLETE WITH JOINTS	M10	Differential side 5.2 - 5.8

Top up the automatic transmission fluid level (refer to op. 2130A04 Automatic transmission FLUID - Check level and top up, .if necessary ). - 7055B54 under-engine guard - r r . - 7055B39 front additional wheel arch half (one), lh or rh, front element - r r (left). - 4450B10 Front WHEEL (one) - R.R. (left).. Connect the battery terminal (-).Remove the car from the ramp.