4130B41 OUTLET PIPE FROM PUMP TO POWER STEERING CASE R R FOR RIGHT HAND DRIVE VERSIONS - Alfa - 166 - eLearn

3314643 - 4130B41 outlet pipe from pump to power steering case r r for right hand drive versions

) Place the car on a ramp with the wheels perfectly straight.Mark the position of the steering wheel in relation to the upper steering column shroud.Ensure that the ignition key is in the OFF position, then disconnect the negative (-) battery terminal.

	Name	Connector
-	Battery	A1B

Draw off the fluid from the power assisted steering reservoir using a suitable syringe.1. Undo bolts (1a), remove plastic pin (1b) and remove the under-facia lining driver side (1c).

Remove the driver side carpet.1. Undo bolts (1a) and remove the driver side footrest (1b).2. Undo bolts (2a) and remove the central console right side cover (2b)

1. Undo the bolt (1a) and disconnect the steering column (1b) from the power assisted steering box pinion.

The bolt is pretreated and cannot therefore be refitted.

1. Remove retaining ring (1a) and withdraw the fail-safe device (1b) from the steering box pinion.

1. Remove the floor lining, undo the bolts (1a) and remove the power steering box guard (1b) complete with rubber block (1c).

- 7055B54 under-engine guard - r r Guard beneath engine]. - 1076B52 exhaust pipe (one) leaving l/h or r/h exhaust manifold - r + r1. Undo the nuts (1a) and remove the protective heat shield (1b) from the power steering box.

- 1084B30 engine oil filter r r - 4450B10 Front WHEEL (one) - R.R. - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R. - 1092G10 single engine belt r r - 1092G20 engine component single belt fixed tensioner - one - r + r - 5530A14 alternator - r+r for versions with air conditioner1. Release the power steering pipes from the retaining clip.

1. Undo the connector (1a) and disconnect the delivery pipe from pump to power steering box (1b), pump side.

1. Undo the bolt (1a) and remove the band (1b) fixing the power steering pipes.2. Undo the connector (2a) and disconnect the supply pipe from the pump to the power assisted steering box (2b), power assisted steering box side.3. Unscrew the connector (3a) on the return pipe from power steering box to the rigid pipe on the steering box side (3b).

- 7040D12 engine front side cover (one) lh or rh - r r1. Release the supply pipe from the pump to the steering box, from the fixing band.

1. Remove the pipe clip.2. Remove the delivery pipe from pump to power steering box withdrawing it from the right front wheel compartment.

Refitting ( Removing

) Place the supply pipe from the pump to the power assisted steering box back in its housing and secure it using the nut.Secure the supply pipe from the pump to the power assisted steering box with the band. Connect the return pipe from power steering box to the rigid pipe on the rigid pipe side.1. Connect the return pipe from power steering box to rigid pipe (1a) power steering box side and secure by tightening fitting (1b) to the specified torque.

	Fastening	Component	Ø	Value(daNm)
1b	Connector	POWER STEERING/EXCHANGE BOX RUBBER HOSE	M12	(Power steering box side) 3.1 - 3.8

2. Connect the supply pipe from the pump to the power assisted steering box (2a), power assisted steering box side, and tighten the connector (2b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2b	Connector	PIPE BTWN PUMP + POWER STEERING BOX	M14	(Power steering box side) 3.1 - 3.8

3. Place the power assisted steering pipes retaining band back in the housing and secure it using the bolts.

1. Connect the delivery pipe from pump to power steering box (1a), and tighten the connector (1b) to the specified torque.

	Fastening	Component	Ø	Value(daNm)
1b	Connector	PIPE BTWN PUMP + POWER STEERING BOX	M16	(Power assisted steering pump side) 3.4 - 4.2

Fix the power assisted steering system pipes using the band. - 5530A14 alternator - r+r for versions with air conditioner - 1092G20 engine component single belt fixed tensioner - one - r + r - 1092G10 single engine belt r r - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R. - 4450B10 Front WHEEL (one) - R.R. - 1084B30 engine oil filter r rRefit the power steering box heat shield in its seat and tighten its nuts. - 1076B52 exhaust pipe (one) leaving l/h or r/h exhaust manifold - r + r - 7055B54 under-engine guard - r r Guard beneath engine]. Place the power steering box pinion protection complete with rubber block back in its housing and secure with the bolts. Place the failsafe device back in its housing and secure it using a circlip.1. Connect the steering column (1a) to the steering box pinion with a new bolt (1b) and tighten to the specified torque.

Ensure the reference points on the steering wheel and the upper half casing are aligned.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	STEERING SHAFTS	M8	(Power steering box pinion side) 2.8 - 3.2

Place the central console right side protection back in its housing and secure it using the bolt.Place the driver side footrest back in its housing and fix it using the bolts.Put the driver side floor carpet back in place.Place the driver side under-facia lining back in place and fix it using the bolts.Connect the negative (-) battery terminal.Fill the power steering circuit with the recommended fluid.

	Type	Component	Name	Qty.
-	Fluid	POWER ASSISTED STEERING CIRCUIT	TUTELA GI/A	-

Bleed the air from the power steering system as described below.With the front wheels raised off the ground, with the engine switched off turn the steering wheel to full lock, left and right, 4-5 times.Check and, if necessary, top up the fluid level in the reservoir.Remove the vehicle from the ramp.Start the engine and carry out 4 - 5 full steering wheel turn cycles (right and left).Top up the fluid level in the reservoir.