W05 WHITE EXHAUST FUMES - Alfa - 166 - eLearn

3308739 - W05 WHITE EXHAUST FUMES

There is a large amount of exhaust fumes, with light coloured smoke

0	PRELIMINARY CHECKS	All OK	Problems met	Operation
		Results of the tests
	First check that there is no water or other fluids in the fuel tank	Continue to Step 1	Presence of dirt in the fuel tank	Clean the fuel tank Op. 1040A24
1	CHECKING WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
2.0 TS 2.0 TB 2.5 V6 3.0 V6 2.5 V6 CAE 3.0 V6 CAE	Connect diagnostic equipment (Examiner or other instruments) to the diagnostic socket. Check that there are no faults in the engine management control unit	Continue to Step 2	An error is detected in the control unit	Continue following the instructions for the diagnostic equipment
2.0 TS 2.0 TB 2.5 V6 3.0 V6 2.5 V6 CAE 3.0 V6 CAE		Continue to Step 2	Lack of dialogue with the control unit	Restore the connection between the engine management control unit and the diagnostic connector See E5030 PETROL ENGINE ELECTRONIC MANAGEMENT
2.4 JTD 10v	Connect diagnostic equipment (Examiner or other instruments) to the diagnostic socket. Check that there are no faults in the engine management control unit	Continue to Step 2	An error is detected in the control unit	Continue following the instructions for the diagnostic equipment
2.4 JTD 10v		Continue to Step 2	Lack of dialogue with the control unit	Restore the connection between the engine management control unit and the diagnostic connector See E5050 DIESEL ENGINES ELECTRONIC MANAGEMENT
2	ACTIVE DIAGNOSIS WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
2.0 TS 2.5 V6 3.0 V6 2.5 V6 CAE 3.0 V6 CAE	Using the diagnostic equipment (Examiner or other instruments) carry out the active diagnosis of the injectors.	Continue to Step 3	Injector connections faulty	Restore the connection of the injectors with the control unit, See E5030 PETROL ENGINE ELECTRONIC MANAGEMENT
2.0 TS 2.5 V6 3.0 V6 2.5 V6 CAE 3.0 V6 CAE		Continue to Step 3	Injectors faulty	Replace injectors Op. 1056B70
3	CHECKING CYLINDER HEAD GASKET	All OK	Problems met	Operation
2.0 TS 2.4 JTD 10v 2.5 V6 CAE 3.0 V6 CAE	Verify: that the cylinder head tightening is correct the gasket seal	Continue to Step 4	Cylinder head tightening not correct	Restore correct tightening
2.0 TS 2.4 JTD 10v 2.5 V6 CAE 3.0 V6 CAE		Continue to Step 4	Gasket damaged	Replace the gasket Op. 1016C11
2.5 V6 3.0 V6	Verify: that the cylinder head tightening is correct the gasket seal	Continue to Step 4	Cylinder head tightening not correct	Restore correct tightening
2.5 V6 3.0 V6		Continue to Step 4	Gasket damaged	Replace the gasket Op. 1016D11
4	CHECKING BLOW-BY CIRCUIT	All OK	Problems met	Operation
	Check the condition of the blow-by gases intake circuit. In particular, check that there are no obstructions in the separator or in the pipes	Continue to Step 5	Blow-by circuit faulty	Restore the operation of the circuit; if necessary, replace the pipes (see Assembly 1080D)
		Continue to Step 5	Fault in the separator	Replace the separator Op. 1080D34
5	CHECK ON CORRECT OPERATION	All OK	Problems met	Operation
	Check that the fault is no longer present	End of diagnosis	Fault persists	Search for the fault starting from another symptom'