1008A44 REAR RIGID MOUNT - R R (AUTOMATIC TRANSMISSION) - Alfa - 166 - eLearn

3314035 - 1008A44 rear rigid mount - r r (Automatic transmission)

) Position the vehicle on the ramp. Make sure that the ignition is OFF (STOP position), then disconnect the negative battery terminal (refer to op. 5530B10 battery - r+r ).

	Name	Connector
-	Battery	A1B

- 7040D12 engine front side cover (one) lh or rh - r r (left). - 7040D14 engine bay rear side cover (one) lh or rh - r r (left). - 7055B54 under-engine guard - r r . - 1084A16 oil dip stick pipe - r r . - 4450B10 Front WHEEL (one) - R.R. (left). - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R. (right) - 1092G10 single engine belt r r . - 5530A14 alternator - r+r for versions with air conditioner . 1. Undo the bolts (1a) and disconnect the right front half shaft (1b) from the intermediate half shaft.

The above bolts have been treated with an eslok type material therefore they should be replaced each time they are removed.

1. Undo the bolts fixing the engine outlet exhaust pipe to the catalytic converter.

1. Undo the bolts fixing the intermediate driveshaft to the rigid rear support for the power unit.2. Undo the bolt (2a) and loosen the bolt (2b) fixing the brackets connecting the oil sump to the power unit rigid rear support.

- 4410A80 damper lower fork - r r (left). 1. Remove the intermediate driveshaft.

Fix the steering knuckle to the upper track control arm, then remove the hydraulic jack.1. Disconnect the electrical connection for the engine oil level sensor.

	Name	Connector
1	Engine oil level sensor	K32

2. Disconnect the electrical connection for the insufficient engine oil pressure switch.

	Name	Connector
2	Insufficient engine oil pressure (switch) sensor	K30

3. Release the electrical wiring from the securing bands.

1. Disconnect the electrical connection from the fuel temperature sensor.

	Name	Connector
1	Fuel temperature sensor	K81

2. Disconnect the electrical connection from the fuel pressure regulator.

	Name	Connector
2	Fuel pressure regulator	N77

1. Undo the nut fixing the rear power unit rigid support to the flexible mounting.2. Undo the bolts fixing the power unit rigid rear support to the cylinder block/crankcase.

- 7040D12 engine front side cover (one) lh or rh - r r (left). - 7040D14 engine bay rear side cover (one) lh or rh - r r (left). - 1008C10 power unit upper reaction link r r . - 1008C16 body link bracket - r r . 1. Undo the nut fixing the timing side rigid engine support to the flexible mounting.

1. Undo the upper nut (1a) fixing the pressure pump and fix it using a suitable engine lifting bracket (1b).2. Fit the safety tools (2a) and (2b) for supporting the power unit and connect the rod to the bracket fitted previously.

	Name	Country
2a	Support mountings	1.870.650.000

	Name	Country
2b	Crossmember	1.820.581.000

3. Act on the rod and raise the power unit, as necessary.4. Remove the rigid rear support for the power unit.

Refitting ( Removing

) 1. Place the rigid rear support for the power unit back in its housing.2. Act on the rod and lower the power unit.3. Remove the safety tools (3a) and (3b) for supporting the power unit.

	Name	Country
3a	Support mountings	1.870.650.000

	Name	Country
3b	Crossmember	1.820.581.000

4. Remove the engine lifting bracket.5. Tighten the upper nut fixing the pressure pump to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
5	Nut	PRESSURE PUMP	M8	Support side 2.6 - 3.2

1. Tighten the nut securing timing side rigid engine support to the flexible mounting to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Nut	ENGINE MOUNT TIMING SIDE	M10	(Flexible mounting side) 3.8 - 4.7

- 1008C16 body link bracket - r r . - 1008C10 power unit upper reaction link r r . - 7040D14 engine bay rear side cover (one) lh or rh - r r (left). - 7040D12 engine front side cover (one) lh or rh - r r (left). 1. Tighten the bolts fixing the power unit rigid rear support to the cylinder block/crankcase to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	POWER UNIT RIGID REAR MOUNT	M10	Engine crankcase side 4.3 - 5.3

2. Tighten the nut securing the rear power unit rigid support to the flexible mounting to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2	Nut	POWER UNIT RIGID REAR MOUNT	M10	(Flexible mounting side) 3.8 - 4.7

Connect the electrical connection to the fuel pressure regulator.Connect the electrical connection to the fuel temperature sensor.Place the electrical wiring back in its housing and fix it using the bands.Connect the electrical connection for the insufficient engine oil pressure switch.Connect the electrical connection to the engine oil level sensor.Release the steering knuckle from the temporary fixing with the upper track control arm and support it using a hydraulic jack.Place the intermediate driveshaft back in its housing. - 4410A80 damper lower fork - r r (left). Tighten the screw and the bolt fixing the brackets connecting the oil sump to the power unit rigid rear support.Tighten the bolts fixing the intermediate driveshaft to the power unit rigid rear support to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	INTERMEDIATE DRIVE SHAFT	M8	(Support side) 2.6 - 3.2

Tighten the bolts fixing the engine outlet exhaust pipe to the catalytic converter to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	EXHAUST PIPE TO ENGINE	M8	Catalytic converter side 2.4 - 2.9

1. Place the right front driveshaft (1a) back in its housing and fix it to the intermediate driveshaft tightening the bolts (1b) to the recommended torque.

The above bolts have been treated with an eslok type material therefore they should be replaced each time they are removed.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	FRONT DRIVE SHAFT COMPLETE WITH JOINTS	M10	(Intermediate driveshaft side) 5.2 ÷ 5.8

- 5530A14 alternator - r+r for versions with air conditioner . - 1092G10 single engine belt r r . - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R. (right) - 4450B10 Front WHEEL (one) - R.R. (left). - 1084A16 oil dip stick pipe - r r . - 7055B54 under-engine guard - r r . - 7040D14 engine bay rear side cover (one) lh or rh - r r (left). - 7040D12 engine front side cover (one) lh or rh - r r (left). Connect the battery terminal (-).Remove the car from the ramp.