3314769 - 5040A20 air conditioner compressor - r+r - includes fluid level check and top up if necessary

Follow the safety instructions (  See assembly 5040A   air conditioner coolant circuit ).

Follow the safety instructions (  See assembly 5040A   air conditioner coolant circuit ).

Follow the safety instructions (  See assembly 5040A   air conditioner coolant circuit ).

Removing ( Refitting ) Position the vehicle on the ramp Make sure that the ignition is off (STOP position), then disconnect the negative battery terminal (refer to op.   5530B10  battery - r+r ).

	Name	Connector
-	Battery	A1B

 - 5040A10  Air conditioning refrigerant CIRCUIT - Draining and Refilling .  - 7040D12  engine front side cover (one) lh or rh - r r (left and right)  - 7040D30  engine bay front beam cover - r r - 1088E11  fans with single engine duct - r+r .  - 4450B10  Front WHEEL (one) - R.R. (right).  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. (right).  - 1092G10  single engine belt r r . 1. Disconnect the electrical connection for the air conditioning compressor electro-magnet coupling.

	Name	Connector
1	Air conditioning compressor engagement electro-magnet	L20

2. Undo the bolts (2a) and disconnect the coolant fluid inlet and outlet pipes (2b) from the compressor.

Seal the disconnected connectors, using suitable plugs, to prevent humidity and impurities from entering the system.

3. Undo the bolts (3a) and remove the air conditioning compressor (3b). Refitting ( Removing ) If replacing the compressor, proceed as follows.1. Remove the drain plug and drain the fluid from the compressor.

Manually rotate the compressor to facilitate the removal of all the fluid.

the fluid is extremely hygroscopic: avoid leaving the containers open. Avoid leaving the compressor or any other component disconnected from the system for longer than is strictly necessary.

1. Recover the fluid drained from the compressor in a suitable transparent container (quantity A).2. Drain and recover the fluid from the new compressor (quantity B) in an identical container, following the instructions given previously.3. Introduce the same amount of fluid removed from the compressor being replaced into the new compressor (eliminate quantity C = B - A). 1. Fit the air conditioning compressor (1a) and fix it tightening the bolts (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	AIR CONDITIONER ASSEMBLY COMPRESSOR	M10	Support side 4.3 - 5.3

2. Connect the coolant fluid inlet and outlet pipes (2a) to the compressor and fix them tightening the bolts (2b) to the recommended torque.

Replace the O-Ring seals for the connectors. Only use green coloured seals, resistant to R134A coolant fluid. Lubricate the thread of the connectors using anti-freeze.

	Fastening	Component	Ø	Value(daNm)
2b	Bolt	PIPE FRM DEHYDRAT FILTR/ACCUM TO COMPRES	M6	Compressor side 0.8 - 1.0

	Fastening	Component	Ø	Value(daNm)
2b	Bolt	PIPES FROM COMPRESSOR TO CONDENSOR	M6	Compressor side 0.8 - 1.0

2. Connect the electrical connection for the air conditioning compressor electro-magnet coupling.  - 1092G10  single engine belt r r .  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. (right).  - 4450B10  Front WHEEL (one) - R.R. (right).  - 1088E11  fans with single engine duct - r+r .  - 7040D30  engine bay front beam cover - r r - 7040D12  engine front side cover (one) lh or rh - r r (left and right)  - 5040A10  Air conditioning refrigerant CIRCUIT - Draining and Refilling . Connect the negative (-) battery terminalRemove the car from the ramps.

Follow the safety instructions (  See assembly 5040A   air conditioner coolant circuit ).