3314331 - 1008C18 link mount on engine - r r

Removing ( Refitting ) Place the vehicle on a ramp. Make sure that the ignition is off (STOP position), then disconnect the negative battery terminal (refer to op.   5530B10  battery - r+r ).

	Name	Connector
-	Battery	A1B

 - 7040D12  engine front side cover (one) lh or rh - r r (right)  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right)  - 4450B10  Front WHEEL (one) - R.R. (right)  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. (right)  - 1092G10  single engine belt r r .  - 1092G20  engine component single belt fixed tensioner - one - r + r .  - 7055B54  under-engine guard - r r .  - 1092A12  crankshaft pulley - r+r for versions with air conditioner .  - 1092G14  engine component single belt mobile tensioner - r + r .  - 1008C10  power unit upper reaction link r r .  - 1008C16  body link bracket - r r .  - 1032B14  toothed timing belt - r + r for timing adjustment or replacement versions with air conditioner .  - 1032C30  fixed timing system tensioner - r + r with timing belt removed - 1032C31  fixed timing tensioner - r r .  - 1084A16  oil dip stick pipe - r r .  - 5530A14  alternator - r+r for versions with air conditioner . 1. Undo the bolts (1a) and remove the left side protection (1b) for the timing belt. 1. Undo the bolts (1a) and remove the power steering pump drive pulley (1b).2. Undo the bolts (2a) and move the power assisted steering pump (2b) away from the support. 1. Undo the bolts (1a) and remove the bracket on the engine for the reaction rod and various engine components (1b). Ошибка в шаблоне. В ближайшее время мы ее исправим. (Error in Templaite) Refitting ( Removing ) 1. Fit the bracket on the engine for the reaction rod and various engine components (1a) and fix it tightening the bolts (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	ENGINE LINK AND VARIOUS COMPT.MOUNTS	-	Engine crankcase side-

1. Refit the power steering pump (1a) in its seating and tighten its bolts (1b) to the specified torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	POWER STEERING BOX BOOT	M8	Pressure pump support side 2.1 - 2.6

2. Fit the power steering pump drive pulley (2a) and tighten its bolts (2b) to the specified torque.

	Fastening	Component	Ø	Value(daNm)
2b	Bolt	POWER STEERING PUMP DRIVE PULLEY	M8	(Power steering pump side ) 2.1 ÷ 2.6

Fit the left side protection for the timing belt and fix it using the bolts. - 5530A14  alternator - r+r for versions with air conditioner .  - 1084A16  oil dip stick pipe - r r .  - 1032C31  fixed timing tensioner - r r .  - 1032C30  fixed timing system tensioner - r + r with timing belt removed .  - 1032B14  toothed timing belt - r + r for timing adjustment or replacement versions with air conditioner .  - 1008C16  body link bracket - r r .  - 1008C10  power unit upper reaction link r r .  - 1092G14  engine component single belt mobile tensioner - r + r .  - 1092A12  crankshaft pulley - r+r for versions with air conditioner .  - 7055B54  under-engine guard - r r .  - 1092G20  engine component single belt fixed tensioner - one - r + r .  - 1092G10  single engine belt r r .  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. (right)  - 4450B10  Front WHEEL (one) - R.R. (right)  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right)  - 7040D12  engine front side cover (one) lh or rh - r r (right) Connect the negative (-) battery terminal.Remove the vehicle from the ramp.