7035A18 WINDSCREEN GLASS R R INCLUDING CLEANING OF HOUSING - Alfa - 166 - eLearn

3315164 - 7035A18 windscreen glass r r including cleaning of housing

) - 7055A18 Windscreen base TRIM - R.R. - 5050B34 windscreen wiper arm/s complete with blade - r+r - 7025A66 l/h or r/h bonnet lid support damper (one) - r+r - 7025A14 Bonnet LID - R.R. - 7030B34 sliding roof compartment decorative seal - r+r - 7040E40 modular front courtesy light - r r - 7040E28 courtesy light on sun blind - r r - 7040H32 sliding roof switch door panel - r r - 7040H30 front pillar trim - r r - 7055A10 MOULDING on roof panel (one), left or right - R.R. - 7065C30 interior l/h or r/h grab handle (one) - r+r - 7065C34 l/h or r/h sun blind (one) - r+r - 7065C59 interior rear view mirror with automatic antiglare device - r r - 7065C68 rear view mirror - r+r1. Remove the press-fitted roof panel moulding retaining studs from both sides of the car.

1. Unscrew the three bolts located under the courtesy light which secure the front part of the roof panel.

Protect the facia and wings using covers.1. Working from outside the car, remove the five spacers located between window and body.

1. Working inside the car, use a vibrating cutter ( 1a) with blade (1b) to cut the sealant strip along the sides and on the upper part of the windscreen.

	Name	Country
1a	Vibrating knife	1.823.011.000

	Name	Country
1b	Blade	1.870.691.000

2. Place a set of adhesive tape strips between window and roof panel to prevent the window slipping once the sealant has been cut.3. Disconnect the electrical connection and fold the connector and wires back onto the glass. Secure in place using adhesive tape.

	Name	Connector
3	Heated windscreen	P56

4. Working from outside the car, use the vibrating cutter fitted with a new blade to cut the sealant strip along the bottom of the windscreen. Take care not to cut the wiring previously folded back onto the windscreen.

	Name	Country
4	Blade	1.870.692.000

5. Apply sucker handles to the windscreen.6. Cut the strips of adhesive tape and remove the windscreen with the aid of a second operator.

Refitting ( Removing

) Check the windscreen glass is in good condition.1. Degrease the screen-printed edge of the new windscreen using heptane.2. Fit the locating pins into the threaded sockets in the glass and screw in.3. Apply glass adhesion promoter (primer) (3b) to the screen printed area round the outside using applicator (3a) provided in the kit.

Wait for 15 minutes before carrying out the next operation to give the primer thinner time to evaporate.

1. Use vibrating knife (1a) and blade (1b) to cut and level the sealant strip in the windscreen compartment in order to leave 0.25 /1 mm thickness without scratching the paint. The sealant left in the housing will act as a backing for the new bond.

	Name	Country
1A	Vibrating knife	1.823.011.000

	Name	Country
1B	Blade	1.870.691.000

2. Clean the windscreen housing carefully using compressed air and degrease thorougly using heptane.Touch up the paintwork if necessary.

1. Fit the five spacers (1a) removed previously in the windcreen housing using double-sided adhesive tape (1b).Fit the three clips securing the trim moulding.2. Fit the trim moulding at the top of the window.3. Use an air gun to extrude a sealant strip around the edge of the windscreen. Begin from the lower edge of the windscreen.4. Working with the aid of a second operator, use sucker handles to position the windscreen in its housing immediately after applying the sealant. 5. Fit retaining belt (5a) to apply uniform pressure over the entire windscreen in order to ensure effective mating between glass (5b), sealant (5c) and windscreen (5d).

Check for leaks by applying soapy water around the outer edge and then blowing compressed air through from the inside.Tighten the bolts securing the front of the roof panel. - 7065C68 rear view mirror - r+r - 7065C59 interior rear view mirror with automatic antiglare device - r r - 7065C34 l/h or r/h sun blind (one) - r+r - 7065C30 interior l/h or r/h grab handle (one) - r+r - 7055A10 MOULDING on roof panel (one), left or right - R.R. - 7040H30 front pillar trim - r r - 7040H32 sliding roof switch door panel - r r - 7040E28 courtesy light on sun blind - r r - 7040E40 modular front courtesy light - r r - 7030B34 sliding roof compartment decorative seal - r+r - 7025A14 Bonnet LID - R.R. - 7025A66 l/h or r/h bonnet lid support damper (one) - r+r - 5050B34 windscreen wiper arm/s complete with blade - r+r - 7055A18 Windscreen base TRIM - R.R.