3314038 - 1008B10 power unit front mount (timing side) flexible block - replace (Automatic transmission)

Removing ( Refitting ) Position the vehicle on the ramp.Ensure that the ignition key is in the OFF position, then disconnect the negative battery terminal (-).

NameConnector
-Battery  A1B 
Proceed with the removal  - 7040D12  engine front side cover (one) lh or rh - r r (Left and right sides). Proceed with the removal  - 7040D14  engine bay rear side cover (one) lh or rh - r r (Left and right sides). Proceed with removal  - 1008C10  power unit upper reaction link r r . Proceed with removal  - 1008C16  body link bracket - r r . Proceed with removal - 4450B04 right front wheel r r . Proceed with the removal  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (Right side). 1. Undo the nut fixing the rear power unit rigid support to the flexible mounting.2. Loosen the band fixing the right driveshaft boot to the intermediate driveshaft.
1. Undo the nut fixing the power unit timing side rigid support to the flexible mounting.
Proceed with removal  - 7055B54  under-engine guard - r r . 1. Undo the bolts fixing the exhaust pipe between the precatalyzer and the catalyzer, catalytic converter side.
1. Undo the upper nut (1a) fixing the pressure pump and fix it using a suitable engine mounting bracket (1b).2. Fit the safety tools (2a) and (2b) for supporting the engine and connect the rod to the bracket (2c) fitted previously.

NameCountry
2aSupport mountings1.870.650.000

NameCountry
2bCrossmember1.820.581.000
Using the rod, raise the engine as necessary to release the timing side power unit rigid support from the stud for the flexible mounting.
1. Undo the bolts (1a) and remove the flexible mounting for the power unit front support (1b).
Refitting ( Removing ) 1. Place the flexible mounting for the power unit front support (1a) back in its housing and secure it by tightening the bolts (1b) to the recommended torque.

FasteningComponentØValue(daNm)
1bBoltFRONT RUBBER MOUNTSM10
Using the rod, lower the engine as necessary to insert the timing side power unit rigid support in the stud for the flexible mounting.1. Remove the safety tools (1a) and (1b) used for supporting the power unit.

NameCountry
1aSupport mountings1.870.650.000

NameCountry
1bCrossmember1.820.581.000
2. Remove the engine lifting bracket.3. Tighten the upper nut fixing the pressure pump to the recommended torque.

FasteningComponentØValue(daNm)
3NutPRESSURE PUMPM8Support side 2.6 - 3.2
1. Tighten the bolts fixing the exhaust pipe between the precatalyzer and the catalyzer to the catalytic converter to the recommended torque.

FasteningComponentØValue(daNm)
1BoltPRE-CAT CONVERTOR/CAT CONVERTOR PIPEM8
1. Undo the nut fixing the timing side rigid power unit support to the flexbile mounting to the specified torque.

FasteningComponentØValue(daNm)
1----
1. Tighten the band fixing the right driveshaft boot to the intermediate driveshaft.2. Tighten the nut securing the rear power unit rigid support to the flexible mounting to the recommended torque.

FasteningComponentØValue(daNm)
2----
Proceed with the refitting  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (Right side). Proceed with refitting - 4450B04 right front wheel r r . Proceed with refitting  - 7055B54  under-engine guard - r r . Proceed with refitting  - 1008C16  body link bracket - r r . Proceed with refitting  - 1008C10  power unit upper reaction link r r . Proceed with the refitting  - 7040D14  engine bay rear side cover (one) lh or rh - r r (Left and right side). Proceed with the refitting  - 7040D12  engine front side cover (one) lh or rh - r r (Right and left sides). Connect the negative (-) battery terminal.Remove the car from the ramps.