1008A44 REAR RIGID MOUNT - R R (AUTOMATIC TRANSMISSION) - Alfa - 166 - eLearn

3314035 - 1008A44 rear rigid mount - r r (Automatic transmission)

) Position the vehicle on the ramp.Ensure that the ignition key is in the OFF position, then disconnect the negative battery terminal (-).

	Name	Connector
-	Battery	A1B

Proceed with the removal - 7040D12 engine front side cover (one) lh or rh - r r (Right side). Proceed with the removal - 7040D14 engine bay rear side cover (one) lh or rh - r r (Right side). Proceed with removal - 7055B54 under-engine guard - r r . Proceed with removal - 1084A16 oil dip stick pipe - r r . Proceed with removal - 4450B04 right front wheel r r . Proceed with the removal - 7055B39 front additional wheel arch half (one), lh or rh, front element - r r (Right side). Proceed with removal - 1092G10 single engine belt r r . Proceed with removal - 5530A14 alternator - r+r for versions with air conditioner . 1. Loosen the band (1a) and disconnect the right front driveshaft (1b) from the intermediate driveshaft.

1. Undo the bolts fixing the exhaust pipe between the precatalyzer and the catalyzer, catalyzer side.

1. Undo the bolts fixing the intermediate driveshaft to the rigid rear support for the power unit.2. Undo the bolt (2a) and loosen the bolt (2b) fixing the brackets connecting the oil sump to the power unit rigid rear support.

Proceed with the removal - 4410A80 damper lower fork - r r (Right side). 1. Remove the intermediate driveshaft.

Fix the steering knuckle to the upper track control arm, then remove the hydraulic jack.1. Disconnect the electrical connection for the engine oil level sensor.

	Name	Connector
1	Engine oil level sensor	K32

2. Disconnect the electrical connection for the insufficient engine oil pressure switch.

	Name	Connector
2	Insufficient engine oil pressure (switch) sensor	K30

3. Release the electrical wiring from the retaining bands.

1. Undo the nut fixing the rear power unit rigid support to the flexible mounting.2. Undo the bolts fixing the power unit rigid rear support to the cylinder block/crankcase.

Proceed with removal - 1008C10 power unit upper reaction link r r . Proceed with removal - 1008C16 body link bracket - r r . 1. Undo the nut fixing the timing side rigid engine support to the flexible mounting.

1. Undo the upper nut (1a) fixing the pressure pump and fix it using a suitable engine lifting bracket (1b).2. Fit the safety tools (2a) and (2b) for supporting the power unit and connect the rod to the bracket fitted previously.

	Name	Country
2a	Support mountings	1.870.650.000

	Name	Country
2b	Crossmember	1.820.581.000

3. Act on the rod and raise the power unit, as necessary.4. Remove the rigid rear support for the power unit.

Refitting ( Removing

) 1. Place the rigid rear support for the power unit back in its housing.2. Adjust the rod and place the power unit back in its housing.3. Remove the safety tools (3a) and (3b) for supporting the power unit.

	Name	Country
3a	Support mountings	1.870.650.000

	Name	Country
3b	Crossmember	1.820.581.000

4. Remove the engine lifting bracket.5. Tighten the upper nut fixing the pressure pump to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
5	Nut	PRESSURE PUMP	M8	Support side 2.6 - 3.2

1. Tighten the nut securing timing side rigid engine support to the flexible mounting to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Nut	ENGINE MOUNT TIMING SIDE	M10	(Flexible mounting side) 3.8 - 4.7

Proceed with refitting - 1008C16 body link bracket - r r . Proceed with refitting - 1008C10 power unit upper reaction link r r . 1. Tighten the bolts fixing the power unit rigid rear support to the cylinder block/crankcase to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	POWER UNIT RIGID REAR MOUNT	M10	(Engine crankcase side) 4.3 ÷ 5.3

2. Tighten the nut securing the rear power unit rigid support to the flexible mounting to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2	Nut	POWER UNIT RIGID REAR MOUNT	M10	(Flexible mounting side) 3.8 ÷ 4.7

Place the electrical wiring back in its housing and fix it using the bands.Connect the electrical connection for the insufficient engine oil pressure switch.Connect the electrical connection to the engine oil level sensor. Release the steering knuckle from the temporary fixing with the upper track control arm and support it using a hydraulic jack.Place the intermediate driveshaft back in its housing. Proceed with the refitting - 4410A80 damper lower fork - r r (Right side). Tighten the screw and the bolt fixing the brackets connecting the oil sump to the power unit rigid rear support.Tighten the bolts fixing the intermediate driveshaft to the power unit rigid rear support to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	INTERMEDIATE DRIVE SHAFT	M8	(Support side) 2.6 - 3.2

Tighten the bolts fixing the exhaust pipe between the precatalyzer and the catalyzer, catalyzer side to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	-	-	-	-

Place the right front driveshaft back in its housing and tighten the band. Proceed with refitting - 5530A14 alternator - r+r for versions with air conditioner . Proceed with refitting - 1092G10 single engine belt r r . Proceed with the refitting - 7055B39 front additional wheel arch half (one), lh or rh, front element - r r (Right side). Proceed with refitting - 4450B04 right front wheel r r . Proceed with refitting - 1084A16 oil dip stick pipe - r r . Proceed with refitting - 7055B54 under-engine guard - r r . Proceed with the refitting - 7040D14 engine bay rear side cover (one) lh or rh - r r (Right side). Proceed with the refitting - 7040D12 engine front side cover (one) lh or rh - r r (Right side). Connect the negative (-) battery terminal.Remove the car from the ramps.