3314533 - 2710A10 drive shaft with joints (one), l/h or r/h - r + r

Removing ( Refitting ) Position the vehicle on the ramp. - 4450B10  Front WHEEL (one) - R.R. .  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r .  - 7055B54  under-engine guard - r r . 1. Relieve the staking and undo the nut securing the drive shaft to the vertical link.2. Undo the drive shaft bolts.
The above bolts are treated with eslok anti-slackening material and must therefore be replaced whenever they are removed.
3. Remove the safety plates.
 - 4410A80  damper lower fork - r r . Lift the vertical link using a hydraulic jack and attach it temporarily to the upper wishbone.1. Rotate the brake disc to the left and withdraw the drive shaft complete with couplings.
Refitting ( Removing ) Refit the drive shaft complete with couplings in its seating.Release the vertical link from the upper wishbone and lower it on the hydraulic jack. - 4410A80  damper lower fork - r r . Removing ( Refitting ) Position the vehicle on the ramp.PROCEED AS FOLLOWS FOR THE RIGHT DRIVESHAFT. Proceed with removal - 4450B04 right front wheel r r . Proceed with the removal  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (Right side). Proceed with removal  - 7055B54  under-engine guard - r r . PROCEED AS FOLLOWS FOR THE LEFT DRIVESHAFT. Proceed with removal - 4450B02 left front wheel r r . Proceed with removal  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (Left side). Proceed with removal  - 7055B54  under-engine guard - r r . WORK IN THE SAME WAY FOR BOTH DRIVESHAFTS.1. Relieve the staking and undo the nut securing the drive shaft to the vertical link.2. Loosen the driveshaft boot fastening band.
Proceed with removal  - 4410A80  damper lower fork - r r . Lift the vertical link using a hydraulic jack and attach it temporarily to the upper wishbone.Rotate the brake disc to the left and withdraw the drive shaft complete with couplings. Refitting ( Removing ) Refit the drive shaft complete with couplings in its seating.Release the vertical link from the upper wishbone and lower it on the hydraulic jack. Proceed with refitting  - 4410A80  damper lower fork - r r . Tighten the driveshaft boot fastening band.1. Tighten the nut (1a) securing the drive shaft to the wheel hub to the specified torque, using tool (b) for the angle tightening.

FasteningComponentØValue(daNm)
1aNutFRONT DRIVE SHAFT COMPLETE WITH JOINTSM24Hug steering knuckle side 6.7 - 7.3 + 50°

NameCountry
1bProtractor1.820.622.000
1. Using a chisel, stake the collar of the nut in two places as shown in the figure.
PROCEED AS FOLLOWS FOR THE LEFT DRIVESHAFT. Proceed with refitting  - 7055B54  under-engine guard - r r . Proceed with the refitting  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (Left side). Proceed with refitting - 4450B02 left front wheel r r . Remove the car from the ramps.PROCEED AS FOLLOWS FOR THE RIGHT DRIVESHAFT. Proceed with refitting  - 7055B54  under-engine guard - r r . Proceed with the refitting  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (Right side). Proceed with refitting - 4450B04 right front wheel r r . Remove the car from the ramps.