3314769 - 5040A20 air conditioner compressor - r+r - includes fluid level check and top up if necessary

Follow the safety instructions (  See assembly 5040A   air conditioner coolant circuit ).

Follow the safety instructions (  See assembly 5040A   air conditioner coolant circuit ).

Follow the safety instructions (  See assembly 5040A   air conditioner coolant circuit ).

Follow the safety instructions (  See assembly 5040A   air conditioner coolant circuit ).

Removing ( Refitting ) Position the vehicle on the rampEnsure that the ignition key is in the OFF position, then disconnect the negative battery terminal (-).

	Name	Connector
-	Battery	A1B

Proceed with the removal  - 7040D12  engine front side cover (one) lh or rh - r r (Right side). Proceed with removal  - 7040D30  engine bay front beam cover - r r . Proceed with removal  - 0010T84  coolant for air conditioning system dehydrate and recharge . Proceed with removal - 4450B04 right front wheel r r . Proceed with the removal  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (Right side). Proceed with removal  - 1092G10  single engine belt r r . Proceed with removal  - 7055B54  under-engine guard - r r . Proceed with removal - 7210E10 R.R. FRONT BUMPER . 1. Undo the bolt (1a) and disconnect the pipe from the expansion valve to the air conditioning compressor (1b), compressor side.2. Undo the bolt (2a) and disconnect the pipe from the air conditioning compressor to the condenser (2b), compressor side.

Seal the disconnected connectors, using suitable plugs, to prevent humidity and impurities from entering the system.

1. Disconnect the electrical connection for the air conditioning compressor electromagnet coupling.

	Name	Connector
1	Air conditioning compressor engagement electro-magnet	L20

2. Undo the upper bolts fixing the air conditioning compressor. 1. Undo the nuts (1a) and disconnect the cooling radiator engine oil supply and return pipes (1b), oil filter mounting side.

Collect the engine oil which comes out in a suitable container.

1. Undo the bolt (1a) and remove the bracket (1b) fixing the engine oil supply and return pipes to the cooling radiator. 1. Undo the bolts (1a) and remove the engine oil cooling radiator (1b) complete with pipes (1c). 1. Undo the lower air conditioning compressor fixing bolts.2. Remove the air conditioning compressor. Refitting ( Removing ) If replacing the compressor, proceed as follows.1. Remove the drain plug and drain the fluid from the compressor.

Manually rotate the compressor to facilitate the removal of all the fluid.

the fluid is extremely hygroscopic: avoid leaving the containers open. Avoid leaving the compressor or any other component disconnected from the system for longer than is strictly necessary.

1. Recover the fluid drained from the compressor in a suitable transparent container (quantity A).2. Drain and recover the fluid from the new compressor (quantity B) in an identical container, following the instructions given previously.3. Introduce the same amount of fluid removed from the compressor being replaced into the new compressor (eliminate quantity C = B - A). 1. Place the air conditioning compressor (2a) back in its housing and fix it tightening the bolts (2b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	AIR CONDITIONER ASSEMBLY COMPRESSOR	M8

Place the engine oil cooling radiator complete with pipes back in its housing and fix it using the bolts.Place the cooling radiator engine oil supply and return pipes mounting bracket back in its housing and secure it using the bolt.Connect the engine oil supply and return pipe to the cooling radiator, oil filter mounting side and secure it using the nuts.Connect the electrical connection to the air conditioning compressor electromagnet coupling.1. Connect the pipes from the air conditioning compressor to the condenser (1a), compressor side and secure them tightening the bolt (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	-	-	-	-

2. Connect the pipe from the exapnsion valve to the air conditioning compressor (2a), compressor side and tighten the bolt (2b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2b	-	-	-	-

Proceed with refitting - 7210E10 R.R. FRONT BUMPER . Proceed with refitting  - 1092G10  single engine belt r r . Proceed with the refitting  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (Right side). Proceed with refitting - 4450B04 right front wheel r r . Proceed with refitting  - 0010T11  engine oil check level and top up . Proceed with refitting  - 0010T84  coolant for air conditioning system dehydrate and recharge . Proceed with the refitting  - 7040D14  engine bay rear side cover (one) lh or rh - r r (Right side). Proceed with refitting  - 7040D30  engine bay front beam cover - r r . Proceed with refitting  - 7055B54  under-engine guard - r r . Connect the negative (-) battery terminalRemove the car from the ramps.