2110A11 MANUAL GEARBOX WITH DIFFERENTIAL - R R FOR VERSIONS WITH HYDRAULIC SELECTION - Fiat - PANDA - eLearn

2752661 - 2110A11 manual gearbox with differential - r r for versions with hydraulic selection

) - 5530B10 battery - r+r - 5530B56 BATTERY DRIP TRAY COVER - R.R. - 5530B52 Battery DRIP TRAY/SUPPORT - R.R. - 2127C40 hydraulic speed selection hydraulic actuator unit and clutch - r r1. Open the protective cover.2. Undo the fixing nut (2a) and disconnect the starter motor electrical wiring (2b).

	Name	Connector
2b	Starter' motor	A20A

	Name	Connector
2b	Starter' motor	A20B

	Name	Connector
2b	Starter' motor	A20C

3. Disconnect the electrical connection for the speedometer sensor.

	Name	Connector
3	Speedometer sensor	K84

4. Undo the bolts (4a) fixing the starter motor (4b) and remove it.

- 1072C44 exhaust manifold heat shield on bulkhead - r+r - 7055A42 front grille - r+r1. Unscrew the retaining nut.2. Fit the tool for releasing the steering track rod ends.

	Name	Country
2	Extractor	1.871.000.700

3. Release the steering track rod ends from the wheel hub.4. Undo the fixing bolts (4a) and release the front steering knuckle (4b) from the shock absorber (4c). Work in the same way on both sides of the vehicle.

Vehicle left side.1. Open the bands fastening the coupling boot.2. Release the driveshaft from the differential side joint.

Work in the same way for the right side of the vehicle as described above for the left side, carrying out the following operation first:1. Undo the fixing nut (1a) and the fixing bolts (1b) and move the wheel arch liner (1c) aside.

1. Undo the fixing bolts (1a) and remove the timing dust guard (1b).

- 1024B54 engine flywheel protection r r - 1008C32 GEARBOX LOWER REACTION ROD ' -R.R.1. Undo the fixing bolts (1a) and move the lock (1b) aside.2. Fit the tool (2a), complete with support mountings (2b).

	Name	Country
2a	Crossmember	1.870.595.000

	Name	Country
2b	Support mountings	1.870.650.000

3. Fit the tools (3a) and (3b), then connect them to the tool fitted previously.

	Name	Country
3a	Crossmember	1.860.851.003

	Name	Country
3b	Vertical support	1.871.001.300

Secure the engine, using the special hooks and brackets/chains taking great care to ensure that the engine is properly balanced.

1. Undo the upper bolts securing the gearbox to the engine.

1. Undo the bolt fixing the gearbox side power unit rigid support flexible mounting.

1. Undo bolts (1a) securing engine mount (1b) to the gearbox and remove

1. Undo the fixing bolts (1a) and remove the clutch cable mounting bracket (1b).2. Using a special hydraulic lift (2a), position the gearbox support tools (2b).

	Name	Country
2b	Gearbox mount	1.860.873.000

1. Undo the remaining fixing bolts (1a) and the nut and lower the assembly taking care not to damage any interfering components, then remove the gearbox-differential assembly (1b).

Refitting ( Removing

) Position the gearbox and differential assembly fastened to the tools used for the removal in the engine compartment, and fit it in place taking care not to damage surrounding components. Centre the gearbox-differential unit on the centring pins and secure it, tightening the lower nut and bolts to torque.

To facilitate centring the pins on the engine and the gearbox shaft and the clutch driven plate, move the gearbox-differential unit slightly.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	MANUAL GEARBOX	M12 x 1.25	(below gearbox) 8

	Fastening	Component	Ø	Value(daNm)
-	Nut	MANUAL GEARBOX	M12 x 1.25	(below gearbox) 8

Remove the tool positioned previously for manoeuvring the gearbox during the removal stage.

	Name	Country
-	Gearbox mount	1.860.873.000

Tighten to torque the top bolts securing the gearbox to the engine block.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	MANUAL GEARBOX	M12 x 1.25	(upper gearbox) 8

Fit the gearbox side power unit rigid support in place.Tighten the bolts fixing the support to the gearbox to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	POWER UNIT GEAR BOX END RIGID MOUNT	M10 x 1.25	(Gearbox side) 5

- 1008C32 GEARBOX LOWER REACTION ROD ' -R.R. - 1024B54 engine flywheel protection r rTighten the bolt fixing the rigid support to the gearbox side flexible mounting to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	POWER UNIT GEAR BOX END RIGID MOUNT	M12 x 1.25	(Flexible block side) 8

Remove the power unit anchoring bracket fitted previously.Remove the tools supporting the power unit previously fitted.

	Name	Country
-	Crossmember	1.870.595.000

	Name	Country
-	Support mountings	1.870.650.000

	Name	Country
-	Crossmember	1.860.851.003

	Name	Country
-	Vertical support	1.871.001.300

Position the bonnet catch in its seating and tighten the fixing bolts.Work in the same way on both sides of the vehicle as illustrated below:Fit the driveshaft in place in the differential side joint.Refit the joint boot fastening band.Position the front hub steering knuckle in the housing in the shock absorber and tighten the fixing bolts to torque.

	Fastening	Component	Ø	Value(daNm)
-	Nut	FRONT HUB WITH BEARINGS	M10 x 1.25	7.5

Fit the steering track rod ends in place and tighten the fixing nut to torque.

	Fastening	Component	Ø	Value(daNm)
-	Nut	ADJUSTABLE STEERING LINKS	M10 x 1.25	4

- 7055A42 front grille - r+r - 1072C44 exhaust manifold heat shield on bulkhead - r+rConnect the electrical connection of the speedometer sensor.

	Name	Connector
-	Speedometer sensor	K84

Fit the starter motor in place and tighten the fixing bolts to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	STARTER MOTOR	M8	2,7

Connect the electrical wiring to the starter motor and tighten the fixing nut.

	Name	Connector
-	Starter' motor	A20A

	Name	Connector
-	Starter' motor	A20B

	Name	Connector
-	Starter' motor	A20C

Fit the timing dust guard in place and tighten the fixing bolts.Fit the mounting bracket for the ball joints in place.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	GEAR ENGAGEMENT ASSEMBLY CABLE	M8	3

Fit the ball joints for the gear selection and engagement flexible cables in place. - 2127C40 hydraulic speed selection hydraulic actuator unit and clutch - r r - 0010T21 coolant check density and top up if necessary - 0010T47 hydraulic system fluid for gearbox with hydraulic selection check level and top up if necessary - 0010T48 hydraulic system for gearbox with hydraulic selection bleed air - 5530B52 Battery DRIP TRAY/SUPPORT - R.R. - 5530B56 BATTERY DRIP TRAY COVER - R.R. - 5530B10 battery - r+rRemove the vehicle from the lift.