1060G90 DIESEL INJECTION WIRING HARNESS - R R - Fiat - PANDA - eLearn

2752612 - 1060G90 diesel injection wiring harness - r r

) Remove the car from the ramps. - 5530B10 battery - r+r - 5530B52 Battery DRIP TRAY/SUPPORT - R.R.1. Disconnect the electrical connection from the air flow meter.

	Name	Connector
1	Air flow meter	K41

2. Loosen the band and disconnect the the turbocharger air inlet sleeve from the rigid pipe, air flow meter side.

1. Remove the air filter (1a) complete with air flow meter (1b) by releasing from the underlying pins and then from the rear fastenings.

1. Disconnect the electrical connections (1a) and (1b) from the heater plugs control unit.

	Name	Connector
1a	Plug preheating control unit	M15A

	Name	Connector
1b	Plug preheating control unit	M15B

1. Open the securing band (1a) and disconnect the coolant pipe (1b) fromthe expansion tank.2. Disconnect the two rapid connectors for the fuel pipes from the filter.3. Disconnect the rapid connector for the coolant pipe from the thermostat unit.4. Disconnect the rapid connector for the fuel pipe from the pressure pump.5. Disconnect the rapid connectors (5a) and (5b) from the fuel pipe.6. Undo the fixing bolts (6a) and remove the protective duct (6b) and pipes.

1. Release the electrical wiring (1a) from the band (1b).2. Loosen the band fastening the air intake hose to the turbocharger, turbocharger side.3. Loosen the band fastening oil vapour hose between the rigid pipe and the turbo inlet hose, turbo inlet hose side.4. Disconnect and remove the turbocharger inlet hose.

1. Disconnect the electrical connection from the engine coolant temperature sensor.

	Name	Connector
1	Engine coolant temperature sensor/sender unit	K36

2. Disconnect the electrical connection for the rpm sensor.

	Name	Connector
2	Rpm sensor	K46

1. Disconnect the electrical connection from the engine oil pressure warning light switch.

	Name	Connector
1	Engine oil pressure sensor	K28

2. Disconnect the electrical connections from the heater plugs.

	Name	Connector
2	Heater plugs	A40A

	Name	Connector
2	Heater plugs	A40B

	Name	Connector
2	Heater plugs	A40C

	Name	Connector
2	Heater plugs	A40D

3. Disconnect the electrical connections from the injectors.

	Name	Connector
3	Injector	N70A

	Name	Connector
3	Injector	N70B

	Name	Connector
3	Injector	N70C

	Name	Connector
3	Injector	N70D

4. Disconnect the electrical connection from the cam angle sensor.

	Name	Connector
4	Timing sensor	K47

5. Disconnect the electrical connection from the air conditioning compressor engagement electromagnet.

	Name	Connector
5	Air conditioning compressor engagement solenoid	L20

6. Undo the bolts securing the cable pass to the cylinder head.7. Release the system cable loom (7a) from the attachments (7b) and move it aside.

1. Disconnect the electrical connection from the fuel pressure regulator.

	Name	Connector
1	Fuel pressure regulator	N77

2. Disconnect the electrical connection from the E.G.R. valve.

	Name	Connector
2	EGR solenoid	L30

1. Disconnect the electrical connection from the fuel pressure sensor.

	Name	Connector
1	Fuel pressure sensor	K83

2. Disconnect the electrical connection from the excess pressure sensor.

	Name	Connector
2	Turbocharging sensor	K82

1. Undo the nut (1a) and disconnect the electrical connection (1b) from the alternator.

	Name	Connector
1b	Alternator	A10

2. Open the protective cover (2a), undo the nut (2b) and disconnect the electrical connection (2c) from the starter motor.

	Name	Connector
2c	Starter' motor	A20

Release the cable loom from the bands securing it to the air chamber and remove it.

Refitting ( Removing

) Fit the system cable loom in place and secure it to the bands on the air chamber.Connect the electrical connection to the starter motor, secure it with the nut and close the protective cover.

	Name	Connector
-	Starter' motor	A20

Connect the electrical connection to the alternator and secure it using the nut.

	Name	Connector
-	Alternator	A10

Connect the electrical connection to the excess pressure sensor.

	Name	Connector
-	Turbocharging sensor	K82

Connect the electrical connection to the fuel pressure sensor.

	Name	Connector
-	Fuel pressure sensor	K83

Connect the electrical connection to the EGR solenoid.

	Name	Connector
-	EGR solenoid	L30

Connect the electrical connection to the fuel pressure regulator.

	Name	Connector
-	Fuel pressure regulator	N77

Fit the cable loom in place and secure it.Tighten the bolts securing the cable pass to the cylinder head.Connect the electrical connection to the air conditioner compressor electromagnet.

	Name	Connector
-	Air conditioning compressor engagement solenoid	L20

Connect the electrical connection to the cam angle sensor

	Name	Connector
-	Timing sensor	K47

Connect the electrical connections to the injectors.

	Name	Connector
-	Injector	N70A

	Name	Connector
-	Injector	N70B

	Name	Connector
-	Injector	N70C

	Name	Connector
-	Injector	N70D

Connect the electrical connections to the heater plugs.

	Name	Connector
-	Heater plugs	A40A

	Name	Connector
-	Heater plugs	A40B

	Name	Connector
-	Heater plugs	A40C

	Name	Connector
-	Heater plugs	A40D

Connect the electrical connection to the engine oil pressure warning light switch.

	Name	Connector
-	Engine oil pressure sensor	K28

Connect the electrical connection for the rpm sensor.

	Name	Connector
-	Rpm sensor	K46

Connect the electrical connection to the engine coolant temperature sensor.

	Name	Connector
-	Engine coolant temperature sensor/sender unit	K36

Connect the electrical connections to the pre-heating control unit.

	Name	Connector
-	Plug preheating control unit	M15A

	Name	Connector
-	Plug preheating control unit	M15B

Fit the air inlet hose in place and connect it to the turbocharger.Tighten the band fastening the oil vapour hose between the rigid pipe and the turbo inlet hose, turbo inlet hose side.Tighten the band fastening the turbocharger air inlet hose, turbocharger side.Secure the electrical wiring to the band.Fit the protective duct and fuel pipe in place and tighten the fixing bolts.Connect the rapid connectors for the fuel pipes in place on the pressure pump, on the filter and on the recovery manifold.Connect the connectors for the coolant pipe on the expansion tank and on the thermostat unit.Fit the air filter complete with air flow meter in place.Connect the air intake sleeve to the turbocharger, air flow meter side, and tighten the band.Connect the electrical connection to the air flow meter.

	Name	Connector
-	Air flow meter	K41

- 5530B52 Battery DRIP TRAY/SUPPORT - R.R. - 5530B10 battery - r+rRemove the car from the ramps.