1088C40 THERMOSTAT- R + R - Fiat - PANDA - eLearn

2752636 - 1088C40 thermostat- r + r

) Remove the car from the ramps.1. Loosen the band and disconnect the lower radiator coolant outlet hose from the radiator, engine oil heat exchanger end.

Collect the engine coolant in a suitable container.

- 5530B10 battery - r+r - 5530B52 Battery DRIP TRAY/SUPPORT - R.R.1. Disconnect the electrical connection from the air flow meter.

	Name	Connector
1	Air flow meter	K41

2. Loosen the band and disconnect the the turbocharger air inlet sleeve from the rigid pipe, air flow meter side.

1. Remove the air filter (1a) complete with air flow meter (1b) by releasing from the underlying pins and then from the rear fastenings.

1. Undo the bolts fixing the rigid engine oil vapour recirculation pipe.2. Loosen the band and disconnect the engine oil vapour recirculation pipe from the rigid pipe.

1. Undo the bolt fixing the coolant supply pipe to the engine oil heat exchanger to the engine crankcase.2. Loosen bolts (2a) and disconnect the pipe carrying coolant to the engine oil heat exchanger (2b), heat exchanger side, complete with gasket.

1. Disconnect the electrical connection from the engine coolant temperature sensor.

	Name	Connector
1	Engine coolant temperature sensor/sender unit	K36

2. Disconnect the quick-release fitting of the coolant return pipe to the engine coolant reservoir, thermostat side.3. Loosen band and disconnect the upper coolant inlet hose to the radiator, thermostat side. 4. Loosen the band and disconnect the engine oil heat exchanger flexible coolant supply pipe, rigid pipe side. 5. Loosen the band and disconnect the coolant supply pipe to the water/exhaust gas heat exchanger for the E.G.R. system, thermostat side.

1. Undo the bolts (1a) and remove the thermostat (1b) complete with O-Ring.

Refitting ( Removing

) 1. Fit the thermostat (1a) complete with O-ring in position and secure it tightening the bolts (1b) to the specified torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	THERMOSTAT	M8	(Lower cylinder head side) 2.3 ÷ 2.8

Connect the engine coolant supply pipe to the EGR system water/exhaust gas heat exchanger, thermostat side and tighten the band.Connect the coolant supply pipe to the engine oil heat exchanger, thermostat side, and tighten the band. Connect the upper coolant inlet hose to the radiator, thermostat side, and tighten the band. Connect the quick-release fitting on the coolant return pipe to the engine coolant reservoir, thermostat side.Connect the electrical connection to the engine coolant temperature sensor.

	Name	Connector
-	Engine coolant temperature sensor/sender unit	K36

Connect the coolant supply pipe to the engine oil heat exchanger, heat exchanger side, complete with seal, then tighten the bolts.

Fold back the gasket tabs

Tighten the bolt fixing the coolant supply pipe to the engine oil heat exchanger to the cylinder block/crankcase.Connect the engine oil vapour recirculation hose to the rigid pipe and tighten the band.Tighten the bolts securing the engine oil vapour recirculation rigid pipe.Fit the air filter complete with air flow meter in place.Connect the air intake sleeve to the turbocharger, air flow meter side, and tighten the band.Connect the electrical connection to the air flow meter.

	Name	Connector
-	Air flow meter	K41

- 5530B52 Battery DRIP TRAY/SUPPORT - R.R. - 5530B10 battery - r+rRefit the lower coolant outlet sleeve from the radiator, engine oil heat exchanger end, and tighten the band. - 0010T20 coolant changeRemove the car from the ramps.