1056B90 SYSTEM CABLE BUNDLE - R + R - Lancia - MUSA - eLearn

184000948 - 1056B90 SYSTEM CABLE BUNDLE - R + R

) Position the vehicle on the rampProceed with removal Op. 5530B10 BATTERY - R+RProceed with removalProceed with removal Op. 5530B52 BATTERY DRIP TRAY/SUPPORT - R.R.1. Loosen the band and disconnect the engine oil vapour intake pipe and the side of the sleeve from the air cleaner to the intake manifold2. Loosen the band, disconnect the hose from the air filter to the intake manifold, intake manifold side and remove it. Op. 1048A10 AIR CLEANER FILTERING ELEMENT - REPLACE

1. Disconnect the electrical connections from the ignition coils.

	Name	Connector
1	Ignition coil	A30

2. Disconnect the electrical connection from the cam angle sensor.

	Name	Connector
2	Timing sensor.	K47

1. Disconnect the electrical connection for the front Lambda sensor for the catalytic converter.

	Name	Connector
1	Lambda sensor on catalyzer	K17

2. Disconnect the electrical connection for the rear Lambda sensor for the catalytic converter.

	Name	Connector
2	Lambda sensor on catalyzer	K17

1. Disconnect the electrical connection from the engine coolant temperature sensor.

	Name	Connector
1	Engine temperature sender unit	K36

2. Disconnect the electrical connection from the throtle body integrated with the M.D.S.

	Name	Connector
2	Integrated throttle body actuator	N75

1. Disconnect the electrical connections (1a) and (1b) from the injection/ignition system control unit.

	Name	Connector
1a	Engine management control unit	M10A

	Name	Connector
1b	Engine management control unit	M10B

2. Release system wiring loom (2a) from band (2b).3. Undo the nut (3a) and disconnect the earth lead (3b) from the injection-ignition system.4. Disconnect the electrical connection from the fuel vapour solenoid valve.

	Name	Connector
4	Fuel vapour recovery solenoid	L10

1. Undo the nut (1a) and disconnect the earth lead (1b) from the air conditioner compressor.2. Disconnect electrical connection (2a) from the intake air pressure/temperature sensor and release the electrical wiring from band (2b).

	Name	Connector
2a	Integrated air temperature sensor	K43

3. Disconnect the electrical connections from the injectors.

	Name	Connector
3	Injector	N70

1. Open the cover (1a), undo the nuts (1b) and disconnect the electrical connections (1c) for the alternator.

	Name	Connector
1c	Starter' motor	A20

2. Undo nut (2a) and disconnect earth lead (2b).3. Disconnect the electrical connection for the knock sensor.

	Name	Connector
3	Detonation sensor	K50

4. Disconnect the electrical connection from the air conditioning compressor engagement electromagnet.

	Name	Connector
4	Air conditioning compressor engagement electro-magnet	L20

5. Release system wiring loom (5a) from bands (5b) on teh air capacity chamber.

Withdraw the system wiring loom from the throttle body side.1. Disconnect the front engine coupling.

Proceed with removal Op. 4450B04 RIGHT FRONT WHEEL R RProceed with removalProceed with removal Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R.Proceed with removal1. Disconnect the electrical connection for the rpm sensor. Op. 1008B10 POWER UNIT FRONT MOUNT (TIMING SIDE) FLEXIBLE BLOCK - REPLACE2. Disconnect the electrical connection from the engine oil pressure warning light switch. Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R

	Name	Connector
1	Rpm sensor	K46

	Name	Connector
2	Engine oil pressure sensor (switch)	K30

Remove the system cable loom.

Refitting ( Removing

) Place the system cable loom back in its housing.Connect the electrical connection to the engine oil pressure warning light switch.Connect the electrical connection for the rpm sensor.Proceed with refitting Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R.Proceed with refitting Op. 1008B10 POWER UNIT FRONT MOUNT (TIMING SIDE) FLEXIBLE BLOCK - REPLACE.Proceed with refitting Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R..Proceed with refitting Op. 4450B04 RIGHT FRONT WHEEL R R.Connect the front engine coupling.Secure the system wiring harness with fastenings to the air chamber.Connect the electrical connection to the air conditioner compressor electromagnet.Connect the electrical connection for the knock sensor.Connect the earth lead and fix it using the nut.Connect the electrical connection to the starter motor, secure it with the nut and close the protective cover.Connect the electrical connections to the injectors.Connect the electrical connection to the intake air temperature/pressure sensor and secure the electrical wiring with a collar.Connect the earth lead to the air conditioner compressor and fix it using the nut.Connect the electrical connection to the fuel vapour solenoid valve.Connect the earth lead to the injection-ignition system control unit and secure with the nut.Secure the system wiring loom with the band.Connect the electrical connections to the fuel injection/ignition control unit.Connect the electrical connection to the throttle body integral with M.D.S.Connect the electrical connection to the engine coolant temperature sensor.Connect the electrical connection for the rear Lambda sensor for the catalytic converter.Connect the electrical connection for the front Lambda sensor for the catalytic converter.Connect the electrical connection to the cam angle sensor.Connect the electrical connections to the ignition coils.Place the hose from the air filter to the intake manifold back in its housing, connect it to the intake manifold and tighten the band.Connect the engine oil vapour intake pipe on the side of the sleeve from air filter to intake manifold and tighten the band.Proceed with refitting Op. 1048A10 AIR CLEANER FILTERING ELEMENT - REPLACE.Proceed with refitting Op. 5530B52 BATTERY DRIP TRAY/SUPPORT - R.R..Proceed with refitting Op. 5530B10 BATTERY - R+R.Remove the car from the ramps.