D04 ENGINE NOT RUNNING SMOOTHLY - Lancia - MUSA - eLearn

184000415 - D04 ENGINE NOT RUNNING SMOOTHLY

There are decreases in performance during acceleration

0	PRELIMINARY CHECKS	All OK	Problems met	Operation
		Results of the tests
	Check, in order: the condition of the air intake circuit that there are no faults in the air filter whether the diesel pipes are leaking the accelerator pedal travel that there is no water, petrol, paraffin or dirt in the fuel tank and filter that there no obstructions in the exhaust system	Continue to Step 1	Intake air circuit ducts obstructed	Repair the air intake circuit
			Leaks from intake ducts after the compressor	Repair the leak
			Air filter blocked	Replace the filter element Op. 1048A14
			Leaks from intake ducts after the compressor	Repair the leak
			Air filter blocked	Eliminate the cause of the problem
			Air filter blocked	Replace the filter element Op. 1048A14
			Leaks from intake ducts after the compressor	Repair the leak
1	CHECK WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
	Connect the diagnostic equipment (Examiner or other instruments) to the diagnostic socket Check: for errors in the control unit plausibility of all the parameters	Continue to Step 2	Presence of error P0093	Continue to Step 2
			Presence of one of the following errors: P0262, P0265, P0268, P0271	Continue to Step 3
			Presence of error P0504	Continue to Step 4
			Presence of error P1237	Continue to Step 6
			Presence of one of the following errors: P0101, P1102	Continue to Step 7
			Presence of one of the following errors: P0120, P0220, P0226	Continue to Step 8
			Presence of other errors	Continue according to the instructions for the diagnostic equipment
2	HIGH RESSURE CIRCUIT CHECK	All OK	Problems met	Operation
	With the Examiner tester connected to the tester input check: that the diesel pressure parameter is as described in the test 1060D the correct operation of the pressure regulator by means of active diagnostics the correct operation of the injectors through active diagnosis absence of leaks in high pressure circuit	Continue to Step 4	Diesel pressure parameter incorrect	Continue to Step 3
			Pressure regulator defective	Replace the pressure regulator Op. 1060E50
			Leaks in high pressure circuit	Restore system seal
			Faulty injector	Replace the damaged injector Op. 1060F10
3	INJECTOR HIGH PRESSURE CHECK	All OK	Problems met	Operation
	Check, as described in the test See Test 1060C Injector high pressure fuel circuit check , that diesel leaks from the injector recirculation connections are small and about the same as one another.	Continue to Step 4	Large leak from one injector	Replace the injector Op. 1060F10
4	BRAKE SWITCH CHECK	All OK	Problems met	Operation
	With the Examiner connected to the diagnostic socket, check that the brake switch is working properly	Continue to Step 5	Faulty switch	Replace switch Op. 1060G38
		Continue to Step 5	Faulty wiring	Renew the wiring See E5050 DIESEL ENGINES ELECTRONIC MANAGEMENT
5	INJECTOR HIGH PRESSURE CHECK	All OK	Problems met	Operation
	Use an Examiner to check fuel pump power uptake is correct by performing the test See Test 1040AA Check supply voltage' and absorption current'	Continue to Step 6	Absorption not correct	Replace the pump Op. 1040A70
6	CHECK EGR	All OK	Problems met	Operation
	With the Examiner diagnostic equipment connected to the diagnostic socket, carry out the active diagnosis of the EGR electric valveCheck the condition of the EGR system, particularly to ensure that the EGR is not blocked open	Continue to Step 7	EGR wiring broken	Restore correct operation See E5050 DIESEL ENGINES ELECTRONIC MANAGEMENT
			EGR valve fault	Replace EGR Op. 1080C74
			EGR system mechanical fault	Restore correct operation
7	CHECK FLOW METER	All OK	Problems met	Operation
	Check that the flow meter is working properly by carrying out the test See Test 1060GB Check on operation of air flow meter	Continue to Step 8	Flow meter signal too high with consequent increased exhaust gas recirculation	Replace the flow meter Op. 1060G10
8	CHECK FLOW METER	All OK	Problems met	Operation
	Check the correct operation of the accelerator pedal potentiometer as described in the test See Test 1068AB Check operation of accelerator pedal potentiometer	Continue to Step 9	Anomalous potentiometer operation	Replace potentiometer Op. 1068A20
		Continue to Step 9	Electrical wiring defective	Renew the wiring See E5050 DIESEL ENGINES ELECTRONIC MANAGEMENT
9	CHECK ON TURBOCHARGER	All OK	Problems met	Operation
	Check the operation of the turbocharger as described in the Test See Test 1064BA Check turbo presure	Continue to Step 11	Turbocharger faulty	Replace the turbocharger unit Op. 1064A19
10	Continue as instructed by the tester	All OK	Problems met	Operation
	Check that the fault is no longer present	End of diagnosis	Fault persists: control unit faulty	Replace control unit Op. 1060G80