1020D17 ENGIND FRONT COVER - R R - Lancia - MUSA - eLearn

184000833 - 1020D17 ENGIND FRONT COVER - R R

) Op. 1004D40 ENGINE - POSITION ON STAND AND REMOVE1. Undo the bolts (1a) and remove the crankshaft pulley (1b).2. Undo the bolt (2a) and remove the single drive belt fixed guide pulley (2b).3. Undo the bolts (2a) and remove the power unit reaction rod attachment bracket (2b).

1. Undo the bolts (1a) and remove the timing drive belt guard (1b).2. Loosen the timing belt tensioner nut.3. Remove the toothed timing drive belt.

1. Undo the bolts (1a) and remove the complete oil dipstick (1b).2. Disconnect the condensation oil return pipe to the sump.

Rotate the engine through 180° on the overhauling stand.1. Undo the front and rear bolts (1a) for the crankcase sump using tool (1b).

	Name	Country
1b	Key	1.860.833.000

2. Undo the side bolts (2a) for the crankcase sump using tool (2b).

	Name	Country
2b	Key	1.860.834.000

3. Remove the crankcase sump (3a).

To loosen the sump from the crankcase, insert tool (3b) between both components using a mallet, then use a screwdriver for leverage in the special projections at the side of the crankcase sump.

	Name	Country
3b	Blade	1.870.718.000

1. Undo the bolts (1a) and remove the crankcase front cover with built in oil pump (1b) and intake housing.Remove the crankshaft front oil seal.

Refitting ( Removing

) Fit the engine block front cover complete with oil pump and intake housing without tightening the bolts.1. Fit a new crankshaft front oil seal (1a) using the tool (1b).

	Name	Country
1b	Fitting tool	1.860.816.000

Tighten the bolts for the crankcase front cover to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	CRANKSHAFT FRONT COVER	M6	0.8 - 1.0

Fit the water - oil heat exchanger and fix it using the pin.Fit the oil filter.Apply sealant to the entire perimeter of the crankcase sump.

	Type	Component	Name	Qty.
-	Silicon sealant	OIL SUMP	-	-

Fit the crankcase sump.Tighten the side bolts for the crankcase sump to torque using the tool.

	Fastening	Component	Ø	Value(daNm)
-	Side bolts	OIL SUMP	M8	2.1 - 2.6

	Name	Country
-	Key	1.860.834.000

Tighten the front and rear bolts for the crankcase sump to torque using the tool.

	Fastening	Component	Ø	Value(daNm)
-	Front and rear bolts	OIL SUMP	M6	0.7 - 0.9

	Name	Country
-	Key	1.860.833.000

Rotate the engine through 180° on the overhauling stand.Connect the condensate oil return pipe to the crankcase sump and secure using a collar.Fit the engine oil dipstick assembly and fix it using the bolts.Fit the auxiliary shaft belt tensioner and fix it using the relevant bolt.Fit the fixed timing belt tensioner and fix it using the relevant bolt.Connect the water inlet and outlet pipes from the water - oil heat exchanger and secure using relevant collars.Fit the power unit support, timing gear side, and fix it using the bolts.1. Fit toothed drive pulley (1a) and tighten the bolt (anticlockwise) (b) to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	TOOTHED DRIVE PULLEY	M16	30.6 - 37.8

Remove the tool.

	Name	Country
-	Counter-torque	1.860.846.000

1. Remove the bolt for the oil pump shown.Temporarily fit the single toothed timing drive belt to the drive pulley.2. Fit the tool.

To allow the engagement of the locating dowel on the timing drive belt drive pulley in the opening in the tool, rotate the crankshaft using small movements.

	Name	Country
-	Template	1.860.905.000

1. Rotate the driven pulley so that the timing references line up.2. Completely fit the timing belt.3. Use a screwdriver to lever in the hole (3a) until the reference on the tensioner (3b) lines up with the reference hole (3c) and, in this position, tighten the belt tensioner nut (3d) to torque.

	Fastening	Component	Ø	Value(daNm)
3d	Nut	MOBILE TIMING TENSIONER	M10	4.2 - 5.2

Remove the tool.

	Name	Country
-	Template	1.860.905.000

Rotate the crankshaft through two revolutions.Check once again that the timing references and the tensioning references on the timing belt tensioner coincide.

Fit the timing drive belt guards and fix them using the bolts.Fit the power unit reaction rod attachment bracket and fix it using the bolts.Fit the engine component single drive belt guide pulley and fix it using the bolt.Fit the crankshaft pulley.Fit the single engine component belt by adjusting the automatic belt tensioner using a wrench.