1020A20 CRANK CASE OIL SUMP - R + R CLEAN SEALS FOR SEALANT APPLICATION - Lancia - MUSA - eLearn

184000824 - 1020A20 CRANK CASE OIL SUMP - R + R CLEAN SEALS FOR SEALANT APPLICATION

) Position the vehicle on the rampEnsure that the ignition key is in OFF position, then disconnect the battery negative terminal (-).

	Name	Connector
-	Battery	A1B

Proceed with removal 1016A10 sound-proofing cover - r + r .Proceed with removal Op. 7055B54 UNDER-ENGINE GUARD - R R.Proceed with removal 1076B70 exhaust pipe between pre-catalytic converter and catalytic converter - r r .Proceed with removal Op. 1084A16 OIL DIP STICK PIPE - R R.1. Undo the engine oil drain plug.

Collect the engine oil in a suitable container.

1. Position a hydraulic jack under the crankcase sump.2. Undo the bolts fixing the crankcase sump to the gearbox.3. Loosen the front and rear bolts (3a) for the crankcase sump using the tool (3b).

	Name	Country
3b	Spanner	1.860.833.001

4. Loosen the side bolts (4a) for the crankcase sump using the tool (4b).

	Name	Country
4b	Spanner	1.860.834.001

5. Use the tool to cut the crankcase sump sealant.

	Name	Country
5	Blade	1.870.718.000

6. Lower the hydraulic jack and remove the crankcase sump.

Refitting ( Removing

) Thoroughly clean the contact surfaces of crankcase sump and cylinder block of sealant residues.Apply silicone sealant around the edge of the crankcase sump.1. Refit the crankcase sump.

When fitting the crankcase sump, avoid major sideways movements which may remove the sealant.

2. Tighten the side bolts (2a) for the crankcase sump to the recommended torque using the tool (2b).

	Fastening	Component	Ø	Value(daNm)
2a	Side bolts	OIL SUMP	M8	(Engine crankcase side) 2.3 ÷ 2.8

	Name	Country
2b	Spanner	1.860.833.001

3. Tighten the front and rear bolts (3a) for the crankcase sump to the recommended torque using the tool (3b).

	Fastening	Component	Ø	Value(daNm)
3a	Front and rear bolt	OIL SUMP	M6	(Crankcase front/rear covers side 08 10

	Name	Country
3b	Spanner	1.860.834.001

4. Tighten the bolts fixing the crankcase sump to the gearbox to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
4	Bolt	OIL SUMP	M10	(Gearbox side) 5.0 ÷ 6.1

5. Remove the hydraulic jack.

Tighten the engine oil drain plug to the specified torque.

	Fastening	Component	Ø	Value(daNm)
-	-	ENGINE OIL DRAIN PLUG	M18	(Crankcase sump side) 1.8 ÷ 2.2

Proceed with refitting Op. 1084A16 OIL DIP STICK PIPE - R R.Proceed with refitting 1076B70 exhaust pipe between pre-catalytic converter and catalytic converter - r r . Op. 0010T11 ENGINE OIL CHECK LEVEL AND TOP UP.Proceed with refitting Op. 7055B54 UNDER-ENGINE GUARD - R R.Proceed with refitting 1016A10 sound-proofing cover - r + r .Connect the negative (-) battery terminalRemove the car from the ramps.