184000876 - 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R

Removing ( Refitting ) Position the vehicle on the ramp    Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM DEHYDRATE AND RECHARGE.Proceed with removal 1016A10 sound-proofing cover - r + r Proceed with removalProceed with removal    Op. 7055B54 UNDER-ENGINE GUARD - R RProceed with removalProceed with removal    Op. 1008A46 CAM SHAFT LEFT RIGID MOUNT - R RProceed with removalProceed with removal    Op. 4450B04 RIGHT FRONT WHEEL R R1. Undo the bolt (1a) and disconnect the pipe from the expansion valve to the compressor (1b), compressor side.    Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R.    Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R. 1092G10 single engine belt r r
Seal the disconnected connectors, using suitable plugs, to prevent humidity and impurities from entering the system.
1. Undo the nut (1a) and disconnect the pipe from the expansion valve to the compressor (1b), expansion valve side.
Seal the disconnected connectors, using suitable plugs, to prevent humidity and impurities from entering the system.
Remove the compressor expansion valve pipe after disengaging it from the intermediate fastenings.
1. Position the tool (1a) on the pressure pump mounting and secure it using the nuts (1b).

NameCountry
1aMount1.860.625.000
2. Fit the tool (2a) complete with support mountings (2b) then connect them to the tool fitted previously using the rod (2c).

NameCountry
2aCrossmember1.870.595.000

NameCountry
2bSupport mountings1.870.650.000
Remove the hydraulic lift from beneath the power unit.1. Undo the bolt (1a) and remove the fixed single drive belt tensioner (1b).
1. Undo the bolts (1a) and remove the lower protective timing cover (1b).
Release the electrical wiring for the cam angle sensor from the fastenings on the upper timing covers.1. Undo the bolts (1a) and remove the upper protective timing covers (1b).
Refitting ( Removing ) Place the upper protective timing covers back in their housings and secure them using the bolts.Secure the cam angle sensor electrical wiring using the fastenings on the upper protective timing covers.Fit the lower protective timing cover and secure using the bolts.1. Place the engine components single drive belt fixed tensioner (1a) back in its housing and fix it tightening the bolt (1b) to the recommended torque.

FasteningComponentØValue(daNm)
1bBoltSINGLE SERVICES MOBILE BELT TENSIONERM82.3 ÷ 2.8
Position the hydraulic lift underneath the power unit.Remove the safety tools used for supporting the power unit.

NameCountry
-Crossmember1.870.595.000

NameCountry
-Support mountings1.870.650.000

NameCountry
-Mount1.860.625.000
Refit the pipe from expansion valve to compressor and secure.1. Connect the pipe from the expansion valve to the compressor (1a), expansion valve side and fix it tightening the nut (1b) to the recommended torque.
Replace the O-rings for the connectors using green coloured seals only, resistant to R134a refrigerant fluid.
Lubricate the thread of the connectors using anti-freeze.

FasteningComponentØValue(daNm)
1bNutEXPANSION VALVE - COMPRESSOR PIPEM6(Expansion valve side) 0.7 ÷ 1.1
1. Connect the pipe from the evaporator pipe connector to the compressor (1a), compressor side and fix it tightening the bolt (1b) to the recommended torque.
Replace the O-rings for the connectors using green coloured seals only, resistant to R134a refrigerant fluid.
Lubricate the thread of the connectors using anti-freeze.

FasteningComponentØValue(daNm)
1bBoltEXPANSION VALVE - COMPRESSOR PIPEM6(Compressor side) 0.7 ÷ 1.1
Proceed with refitting 1092G10 single engine belt r r Proceed with refittingProceed with refitting    Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.Proceed with refittingProceed with refitting    Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R.Proceed with refittingProceed with refitting    Op. 4450B04 RIGHT FRONT WHEEL R R.Remove the car from the ramps.    Op. 1008A46 CAM SHAFT LEFT RIGID MOUNT - R R    Op. 7055B54 UNDER-ENGINE GUARD - R R 1016A10 sound-proofing cover - r + r     Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM DEHYDRATE AND RECHARGE