1060E40 SUPPLEMENTARY PRESSURE PUMP - R R - Lancia - MUSA - eLearn

184000953 - 1060E40 SUPPLEMENTARY PRESSURE PUMP - R R

) Position the vehicle on the ramp.Ensure that the ignition key is in OFF position, then disconnect the battery negative terminal (-).

	Name	Connector
-	Battery	A1B

Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM DEHYDRATE AND RECHARGE.Proceed with removal 1016A10 sound-proofing cover - r + r .Proceed with removal Op. 7055B54 UNDER-ENGINE GUARD - R R.Proceed with removal Op. 1008A46 CAM SHAFT LEFT RIGID MOUNT - R R.Proceed with removal Op. 4450B04 RIGHT FRONT WHEEL R R.Proceed with removal Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R..Proceed with removal Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R..Proceed with removal 1092G10 single engine belt r r .Proceed with removal Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R.Proceed with removal Op. 1032B10 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT.Proceed with removal 1060E30 pressure pump pulley - r r .Proceed with removal Op. 1060F20 PRESSURE PUMP/MANIFOLD PIPE - R R.Proceed with removal Op. 1060E10 PRESSURE PUMP - R R.Proceed with removal 1060F50 fuel return manifold - r r .Proceed with removal 1076B70 exhaust pipe between pre-catalytic converter and catalytic converter - r r .Proceed with removal 2710A35 intermediate drive shaft mount - r r .1. Undo the bolts (1a) and move the bracket (1b) complete with cam angle sensor electrical connection.

1. Undo the nut securing the engine oil dipstick tube to the pressure pump mounting.2. Undo the bolt (2a) and remove the complete engine oil dipstick pipe (2b).

1. Undo the bolt fixing the pressure pump mounting to the cylinder head.

1. Undo the remaining bolts (1a) and remove the pressure pump mounting (1b).

Refitting ( Removing

) Place the pressure pump back mounting back in its housing and secure it by tightening the bolts to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	INJECTION PRESSURE PUMP MOUNT	M8	(Engine crankcase side) 2.3 ÷ 2.8

	Fastening	Component	Ø	Value(daNm)
-	Bolt	INJECTION PRESSURE PUMP MOUNT	M8	(Cylinder head side) 2.3 ÷ 2.8

Place the engine oil dipstick tube in its seating and fix it using the bottom bolt.Tighten the nut securing the engine oil dipstick tube to the pressure pump mounting.Place the bracket complete with cam angle sensor electrical connection back in its seating and tighten the bolts.Proceed with refitting 2710A35 intermediate drive shaft mount - r r .Proceed with refitting 1076B70 exhaust pipe between pre-catalytic converter and catalytic converter - r r .Proceed with refitting 1060F50 fuel return manifold - r r .Proceed with refitting Op. 1060E10 PRESSURE PUMP - R R.Proceed with refitting Op. 1060F20 PRESSURE PUMP/MANIFOLD PIPE - R R.Proceed with refitting 1060E30 pressure pump pulley - r r .Proceed with refitting Op. 1032B10 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT.Proceed with refitting Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R.Proceed with refitting 1092G10 single engine belt r r .Proceed with refitting Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R..Proceed with refitting Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R..Proceed with refitting Op. 4450B04 RIGHT FRONT WHEEL R R.Proceed with refitting Op. 1008A46 CAM SHAFT LEFT RIGID MOUNT - R R.Proceed with refitting Op. 7055B54 UNDER-ENGINE GUARD - R R.Proceed with refitting 1016A10 sound-proofing cover - r + r . Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM DEHYDRATE AND RECHARGE.Connect the negative (-) battery terminal.Remove the car from the ramps.