184000978 - 1060G90 DIESEL INJECTION WIRING HARNESS - R R

Removing ( Refitting ) Position the vehicle on the ramp.Proceed with removal    Op. 5530B10 BATTERY - R+R.Proceed with removal    Op. 5530B52 BATTERY DRIP TRAY/SUPPORT - R.R..Proceed with removal 1016A10 sound-proofing cover - r + r .1. Disconnect the electrical connection for the air conditioning compressor.

NameConnector
1Air conditioning compressor engagement electro-magnet L20
1. Disconnect the electrical connections from the injectors.

NameConnector
1Injector N70
1. Loosen the band and disconnect the oil vapour recirculation pipe from the tappet cover.2. Disconnect the electrical connection from the engine coolant temperature sensor and move the electrical wiring aside.

NameConnector
2Engine temperature sender unit K36
1. Disconnect the electrical connection from the air flow meter.

NameConnector
1Air flow meter K41
2. Disconnect the electrical connection from the turbocharger vane actuator solenoid.

NameConnector
2OVERBOOST solenoid valve L36
Proceed with removal 1080C24 e.g.r. system solenoid - r + r .Proceed with removal 1060F50 fuel return manifold - r r .Proceed with removal 1060G70 vacum tank for controlling engine air intake r r .1. Disconnect the electrical connections from the heater plugs.

NameConnector
1Heater plug A40
1. Disconnect the electrical connection from the pre-heating control unit.

NameConnector
1Plug preheating control unit M15
Remove the heater plugs supply wiring.2. Connect the electrical connections to the diesel electronic injection control unit.

NameConnector
2Engine management control unit M10
1. Disconnect the electrical connection from the cam angle sensor.

NameConnector
1Timing sensor. K47
1. Disconnect the electrical connection from the solenoid on the vacuum tank.

NameConnector
1Butterfly casing solenoid valve L62
2. Disconnect the electrical connection from the excess pressure sensor.

NameConnector
2Turbocharging sensor K82
1. Disconnect the electrical connection from the fuel pressure sensor.

NameConnector
1Fuel pressure sensor K83
2. Disconnect the electrical connection from the fuel pressure regulator.

NameConnector
2Fuel pressure regulator N77
Proceed with removal    Op. 1084A16 OIL DIP STICK PIPE - R R.1. Disconnect the earth lead from the starter motor.

NameConnector
1Starter' motor A20
2. Disconnect the electrical connection for the rpm sensor.

NameConnector
2Rpm sensor K46
3. Disconnect the electrical connection from the engine oil pressure warning light switch.

NameConnector
3Engine oil pressure sensor (switch) K30
4. Disconnect the earth lead from the alternator.

NameConnector
4Alternator A10
Remove the system cable loom after having released it from the fastenings. Refitting ( Removing ) Place the cable loom back in its housing and fix it.Connect the earth lead to the alternator.Connect the electrical connection to the engine oil pressure warning light switch.Connect the electrical connection for the rpm sensor.Connect the earth lead to the starter motor.Proceed with refitting    Op. 1084A16 OIL DIP STICK PIPE - R R.Connect the electrical connection to the fuel pressure regulator.Connect the electrical connection to the fuel pressure sensor.Connect the electrical connection to the excess pressure sensor.Connect the electrical connection to the solenoid on the vacuum tank.Connect the electrical connection to the cam angle sensorConnect the electrical connection to the diesel electronic injection control unit.Refit the heater plugs supply wiring back in its seating.Connect the electrical connection to the pre-heating control unit.Connect the electrical connections to the heater plugs.Proceed with refitting 1060G70 vacum tank for controlling engine air intake r r .Proceed with refitting 1060F50 fuel return manifold - r r .Proceed with refitting 1080C24 e.g.r. system solenoid - r + r .Connect the electrical connection to the turbocharger vane actuator solenoid.Connect the electrical connection to the air flow meter.Refit the electrical wiring in its seating and connect the electrical connection to the coolant temperature sensor.Connect the oil vapour recirculation pipe to the tappet cover and secure with a band.Connect the electrical connections to the injectors.Connect the electrical connection to the air conditioner compressor.Proceed with refitting 1016A10 sound-proofing cover - r + r .Proceed with refitting    Op. 5530B52 BATTERY DRIP TRAY/SUPPORT - R.R..Proceed with refitting    Op. 5530B10 BATTERY - R+R.Remove the car from the ramps.