184001451 - 5530A10 ALTERNATOR - R+R

Removing ( Refitting ) Place the vehicle on a lift.    Op. 4450B04 RIGHT FRONT WHEEL R R    Op. 7055B91 RIGHT FRONT SUPPLEMENTARY WHEEL ARCH R R    Op. 7055B66 ENGINE BAY DUSTGUARD PROTECTION IN RIGHT FRONT WHEEL ARCH R R1. Undo the fixing nuts (1a) and disconnect the exhaust pipe (1b).2. Undo the bolt with nut (2a) for the power unit reaction rod (2b). 1. Slacken the steering tie-rod nut.2. Disconnect steering tie rod (2a) from front hub steering knuckle (2b) using tool (2c).

	Name	Country
2c	Extractor	1.871.000.700

3. Release ABS sensor wiring (3a) from the retainer (3b).4. Undo and remove the bolts with nut fixing the strut to the shock absorber. 1. Remove the right hand drive shaft gaiter boot retaining band.2. Move the power unit (2a) slightly forward and pull drive shaft (2b) to the right, disconnecting it from gearbox joint (2c). 1. Fit a spanner (1a) in the services belt tensioner socket (1b) and rotate it in the direction of the arrow, then release and remove the services belt (1c). 1. Release and remove alternator electrical connections (1a).2. Undo nuts (2a) and disconnect electrical connections (2b) and (2c) from the alternator.

	Name	Connector
2b	Starter'' motor	A20A

	Name	Connector
2c	Starter'' motor	A20B

3. Undo upper bolt (3a) and lower bolts (3b), then remove alternator (3c). Refitting ( Removing ) Check that the alternator is not damaged.1. Place the alternator back in its housing and fix it tightening the bolts to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	ALTERNATOR ASSEMBLY	M10	4.5 ÷ 5.5

2. Connect the electrical connections to the alternator and fix them using the nuts.3. Reclose the electrical connection cover. Refit the service belt, moving the tensioner by inserting the wrench in the fitting.Reconnect the drive shaft to the joint on the gearbox.Position the drive shaft gaiter and secure with the band.1. Refit the bolts with nut securing the strut to the shock absorber and tighten to the specified torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	FRONT HUB STEERING KNUCKLE.	M10	6.2 ÷ 6.8

2. Do up ABS sensor wiring (2b) to retainer (2a).3. Connect steering tie rod (3a) to front wheel hub strut (3b), then tighten nut (3c) and tighten to the specified torque.

	Fastening	Component	Ø	Value(daNm)
3c	Nut	STEERING LINK	M10	3.6 ÷ 4.4

1. Refit the power unit reaction link bolt with nut and tighten.2. Reconnect exhaust pipe (2a) and tighten nuts (2b) to the specified torque.

	Fastening	Component	Ø	Value(daNm)
2b	Nut	EXHAUST PIPE FLANGE	M8	2.3 ÷ 2.8

    Op. 7055B66 ENGINE BAY DUSTGUARD PROTECTION IN RIGHT FRONT WHEEL ARCH R R    Op. 7055B91 RIGHT FRONT SUPPLEMENTARY WHEEL ARCH R R    Op. 4450B04 RIGHT FRONT WHEEL R RRemove the vehicle from the lift. Removing ( Refitting ) Position the vehicle on a lift.    Op. 4450B04 RIGHT FRONT WHEEL R R    Op. 7055B91 RIGHT FRONT SUPPLEMENTARY WHEEL ARCH R R    Op. 7055B66 ENGINE BAY DUSTGUARD PROTECTION IN RIGHT FRONT WHEEL ARCH R R    Op. 1092B40 AIR CONDITIONER COMPRESSOR/ALTERNATOR DRIVE BELT - R + R1. Undo the nuts (1a) and disconnect the exhaust pipe (1b). 1. Unscrew and remove bolt (1a) securing anchorage link (1b). 1. Undo the cover (1a) for the alternator electrical connections and open it.2. Undo the fixing nuts (2a) and disconnect the electrical connections (2b) and (2c) from the alternator.

	Description	Connector
2b	Starter motor	A20A

	Description	Connector
2c	Starter motor	A20B

- Position a column lift and lift the front of the engine.3. Undo the rear bolt (3a) and lower bolts (3b) and remove the power steering pump (3c). Refitting ( Removing ) Check that the alternator is not damaged.1. Place the alternator in position and secure it tightening the bolts to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	ALTERNATOR ASSEMBLY	M10	4.5 ÷ 5.5

2. Connect the electrical connections to the alternator and secure them using the nuts.3. Reclose the electrical connection cover. - Lower the engine.1. Fit the power unit reaction link bolt (1a) in its seat and tighten to the specified torque.

Component	Fastening	Ø	Value (daNm)	Validity
POWER UNIT GEAR BOX END RIGID MOUNT	Nut	M12	(Flexible mounting side) 8.1 ÷ 9.9	1.2 16v1.3 JTD 16v1.4 16v1.9 JTD 8v

1. Reconnect exhaust pipe (1a) and tighten nuts (1b) to the specified torque.

	Fastening	Component	Ø	Value(daNm)
2b	Nut	EXHAUST PIPE FLANGE	M8	2.3 ÷ 2.8

    Op. 1092B40 AIR CONDITIONER COMPRESSOR/ALTERNATOR DRIVE BELT - R + R    Op. 7055B66 ENGINE BAY DUSTGUARD PROTECTION IN RIGHT FRONT WHEEL ARCH R R    Op. 7055B91 RIGHT FRONT SUPPLEMENTARY WHEEL ARCH R R    Op. 4450B04 RIGHT FRONT WHEEL R RRemove the vehicle from the lift.