1032A12 CHAIN AND GEARS FOR TIMING SYSTEM - R.R. FOR TIMING OR REPLACEMENT. - Lancia - MUSA - eLearn

184000859 - 1032A12 CHAIN AND GEARS FOR TIMING SYSTEM - R.R. FOR TIMING OR REPLACEMENT.

) Position the vehicle on the rampMake sure that the ignition key is in the OFF position. then disconnect the battery negative (-) terminal.

	Name	Connector
-	Battery	A1B

Drain the air conditioner coolant circuit Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM DEHYDRATE AND RECHARGE.Proceed with removal Op. 4450B04 RIGHT FRONT WHEEL R RProceed with removalProceed with removal Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R.Proceed with removalProceed with removal Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.Proceed with removalProceed with removal 1092G10 single engine belt r r Proceed with removalProceed with removal Op. 1092A10 CRANKSHAFT SERVICES PULLEY - R.R.1. Undo the bolt securing the driven timing pulley.2. Remove the timing chain (2a) together with the driven timing pulley (2b) and the toothed drive pulley (2c). Op. 7055B54 UNDER-ENGINE GUARD - R R Op. 2110A60 MANUAL GEARBOX/ENGINE COUPLING BRACKET - R+R Op. 1020A20 CRANK CASE OIL SUMP - R + R CLEAN SEALS FOR SEALANT APPLICATION 1020B10 cover of timing system with chain drive - r + r replace oil seal and gasket

Mark the installation position of the exhaust side toothed drive pulley and the toothed drive pulley. If the pulleys are replaced, fit them with the writing turned to the outside.

Using suitable equipment, prepare the moving tensioner and keep it fully retracted using a suitable pin.

Refitting ( Removing

) 1. Refit the timing chain (1a) together with the driven timing pulley (1b) and the toothed drive pulley (1c).2. Tighten the bolt securing the toothed driven pulley to the specified torque.

	Fastening	Component	Ø	Value(daNm)
2	Bolt	TIMING DUCT PULLEY	M12	(Exhaust camshaft side) 10.8 ÷ 13.2

Remove the pin from the moving tensioner and check that the moving tensioner piston is in contact with the plate.Proceed with refitting 1020B10 cover of timing system with chain drive - r + r replace oil seal and gasket .Proceed with refitting Op. 1020A20 CRANK CASE OIL SUMP - R + R CLEAN SEALS FOR SEALANT APPLICATION.Proceed with refitting Op. 2110A60 MANUAL GEARBOX/ENGINE COUPLING BRACKET - R+R.Proceed with refitting Op. 1092A10 CRANKSHAFT SERVICES PULLEY - R.R..Proceed with refitting 1092G10 single engine belt r r .Proceed with refitting Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R..Proceed with refitting Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R..Proceed with refitting Op. 4450B04 RIGHT FRONT WHEEL R R.Connect the negative (-) battery terminal.Refill the engine oil lubrication system Op. 0010T11 ENGINE OIL CHECK LEVEL AND TOP UP.Refill the engine cooling system with coolant Op. 0010T20 COOLANT CHECK DENSITY AND TOP UP IF NECESSARY.Fill the air conditioner coolant circuit Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM DEHYDRATE AND RECHARGE.Proceed with removal Op. 7055B54 UNDER-ENGINE GUARD - R R.Remove the car from the ramps.