7035C14 FIXED REAR SIDE WINDOW ONE LH OR RH R R INCLUDES CLEANING OF HOUSING - Fiat - MULTIPLA - eLearn

2892167 - 7035C14 fixed rear side window one lh or rh r r includes cleaning of housing

) - 7040H42 rear pillar trim - r r - 7040G40 load compartment light bulb holder - r r (left only) - 7040B18 l/h or r/h side trim (one) of luggage compartment/load platform - arrange - 7040B23 back upper side trim (1), lh or rh - r r - 7065C30 interior l/h or r/h grab handle (one) - r+r - 7040E17 lh or rh rear courtesy light - r r (right and left). 1. Undo the bolts on the seat belt cover.2. Remove the cover.3. Remove the retaining buttons using the special tool.

	Name	Country
4	Scraper blade	1.878.077.000

1. Apply adhesive tape to protect the edges of the bodywork along the entire perimeter of the side window.

The bead of sealant on the window can be cut using either harmonic wire or the vibrating knife; both methods are described below.To cut the bead using harmonic wire, proceed as described below.1. Cut a section of harmonic wire about 50 cm long then, using pliers, insert one end (1a) of the harmonic wire through the bead of sealant (1b) which secures the window (1c).2. Secure the end (1a) of the wire to the retaining tool (2a) located inside the car.Secure the end (2b) of the wire to the traction handle (2c) located outside the car.3. The operator inside the car must keep the end of the tool (2a) on the bead of sealant (3a) at about 30 cm from the point of passage of the wire.The other operator outside the car must pull the handle (2c), following the outline fo the window, and cut the bead of sealant (3a).Repeat the operation in sections of about 30 cm, until the whole of the bead of sealant (3a) is cut.During cutting, be careful with the side window's centring pins (3b).4. Fit the suction handles on the windscreen, then with the assistance of a second operator, remove the windscreen and rest it on a supporting stand.

To cut the bead using the vibrating knife, proceed as described below.Because of its particular shape, the side window cannot be reused after removal by vibrating knife.1. Use the vibrating knife (1a), with blade (1b), and cut the bead of sealant (1c) along the whole perimeter of the side window, working from inside the car.During cutting, be careful with the window's centring pins (1d).2. Fit the suction handle on the windscreen, then with the assistance of a second operator, remove the windscreen and rest it on a supporting stand.

Refitting ( Removing

) 1. Using a suitable tool, cut and smooth off the bead of sealant in the side window frame, so as to leave a thickness of between 0.25 and 1 mm, without scratching the paintwork.The sealant left in the frame will act as a backing for the new bond.2. Clean the side window seating carefully with compressed air and thoroughly degrease with heptane.If glueing takes place 60 minutes after cutting and smoothing the bead of sealant, treat the sealant surface with the specific activator and wait 15 minutes before fixing the windscreen.

	Type	Component	Name	Qty.
2	PUR activator	Window compartment	-	-

3. Remove the adhesive tape from the edges of the bodywork along the perimeter of the side window.Touch up the paintwork if necessary.

Check that the window is undamaged.1. Fit locating pins.2. Degrease with heptane the surface of the moulded seal to be glued.3. Apply the activator on the degreased surface.

	Type	Component	Name	Qty.
3	PUR activator	(3RD' FIXED WINDOW)	-	-

Wait about 16 minutes before proceeding with the next operation, to allow the solvent to evaporate.

Avoid touching the treated area with the hands.1. Use an air gun to extrude a bead of sealant as evenly as possible along the perimeter of the window.

	Type	Component	Name	Qty.
7	Window bonding sealant	(3RD' FIXED WINDOW)	Product n. 71711976	-

Begin applying the sealant from the middle of the lower edge and continue without breaks around the entire edge of the window.

1. With the assistance of a second operator, fit the window in its seating immediately after applying the sealant and bed it in place.2. Fit the belt (2a) as shown in the figure and tension it so as to apply even pressure over the entire window, in order to ensure a perfect match between window (2b), sealant (2c) and window frame (2d).

Before refitting the interior components of the car, check that there are no leaks by carrying out a water test.Fit the rear retaining buttons on the ceiling trim.Fit the cover on the central rear seat belt and fixt it with the bolts. - 7040E17 lh or rh rear courtesy light - r r (right and left). - 7065C30 interior l/h or r/h grab handle (one) - r+r - 7040B23 back upper side trim (1), lh or rh - r r - 7040B18 l/h or r/h side trim (one) of luggage compartment/load platform - arrange - 7040G40 load compartment light bulb holder - r r (left only) - 7040H42 rear pillar trim - r r

Wait six hours before moving the car.