2891724 - 4420B34 rear suspension wishbone (one remaining)- r+r following op.4420b30

Removing ( Refitting ) Position the vehicle on the ramp.Completely raise the handbrake lever. - 4450B11  WHEEL (one) rear - R.R. .  - 4450D70  hub cap of one rear wheel, l/h or r/h - r+r . 1. Undo the rear wheel hub nut.
Lower the handbrake lever.Raise the car. - 3320B30  lh or rh rear brake drum (one) r r .  - 4450D10  hub of one rear wheel, l/h or r/h - r+r with wheel removed . 1. Undo the bolt fixing the mounting bracket for the handbrake cable and the brake pipe.2. Remove the rigid pipe for the rear drum brake cylinder from the spring on the track control arm.3. Undo the bolts fixing the brake back plate.4. Remove the brake back plate complete with shoes and brake cylinder and hang it on the bodyshell.
 - 4420A40  l/h or r/h rear suspension coil spring (one) - r+r . 1. Undo the bolt fixing the rear track control arm to the axle.2. Remove the rear track control arm.
Refitting ( Removing )
Before refitting the track control arm, check that there are no cracks or distortions, no signs of wear on the stub axle and that the flexible bushes are intact. If this is not the case, always replace the complete track control arm.
Fit the rear track control arm and fix it using the bolt.Tighten the nut fixing the track control arm to the axle to torque.

FasteningComponentØValue(daNm)
-BoltREAR WISHBONEM16 x 1.515
 - 4420A40  l/h or r/h rear suspension coil spring (one) - r+r . Fit the rear brake back plate complete with shoes and brake cylinder and tighten the fixing bolts to torque.

FasteningComponentØValue(daNm)
-BoltREAR BRAKE CARRIER DISCM82.4
Fit the bolt for the mounting bracket for the handbrake cable and brake pipes and tighten to torque.

FasteningComponentØValue(daNm)
-BoltHANDBRAKE LINKAGE MOUNTSM82.5
Fit the rigid pipe for the rear drum brake cylinder on the spring on the track control arm. - 4450D10  hub of one rear wheel, l/h or r/h - r+r with wheel removed .  - 3320B30  lh or rh rear brake drum (one) r r . Lower the vehicle.Completely raise the handbrake lever.Tighten the rear wheel hub nut to torque.

FasteningComponentØValue(daNm)
-NutREAR WHEEL HUB WITH BEARINGSM22 x 1.528
The rear wheel hub nut should be replaced at each dismantling.
Lower the handbrake lever. - 4450D70  hub cap of one rear wheel, l/h or r/h - r+r .  - 4450B11  WHEEL (one) rear - R.R. . Remove the car from the ramps. Refitting ( Removing ) Place the rear track control arm in its original position and tighten the fixing bolt to the recommended torque.

FasteningComponentØValue(daNm)
-BoltREAR WISHBONEM16 x 1.515
Place the shock absorber spring in its original position.Position the rear flexible mounting and tighten the bolt fixing it to the bodyshell to torque.

FasteningComponentØValue(daNm)
-BoltFLEXIBLE BLOCKS RETAINING AXLE TO BODYM12 x 1.2512.
Position the hydraulic jack under the track control arm, compress the shock absorber spring, then fit the bolt between the shock absorber and the track control arm and tighten it to the recommended torque.

FasteningComponentØValue(daNm)
-NutREAR DAMPERM12 x 1.258.8
Tighten the bolts for the U-bolts securing the anti-roll bar to the track control arm to the recommended torque.

FasteningComponentØValue(daNm)
-BoltREAR ANTI-ROLL BARM83
Tighten the bolts fixing the anti-roll bar to the track control arm to the recommended torque.

FasteningComponentØValue(daNm)
-BoltREAR ANTI-ROLL BARM10 x 1.255.6
Reposition the pipes on the track control arm, close the retaining clips, then tighten the fixing bolt.- 4450D11 one rear wheel hub, lh or rh - r+r with wheels removed for versions with abs Position the rear wheel hub cap. - 3310B59  rear brake disc guard - r r - 3310B48  rear brake disc - r rTighten the bolt fixing the rpm sensor.Tighten the bolt fixing the brake caliper pipe bracket to the disc shield. - 3310B57  rear calliper bracket - r r - 4450B11  WHEEL (one) rear - R.R.Connect the battery negative terminal.

NameConnector
-Battery  A1 
Remove the car from the ramps.