2891815 - 5040B30 expansion valve (tube orifice) - r+r

Removing ( Refitting )  - 7040L20  tunnel trim - r r - 7040A09  passenger air bag compartment cover - r r - 2125C24  gear lever knob - r + r - 7065C10  air conditioning control panel - r+r - 7040A11  control panel lid - r + r - 5560B10  analogue control panel - r+r - 5570T80  car radio unit - r+r - 7040A77  glass holder on facia trim - r r - 7065C42  ashtray (one) r+r - 7010M16  rear electric window enablement switch - r+r - 7040A96  facia glove compartment flap (1) lh or rh - r r (left and right sides)  - 7040A37  fuse box cover - r r - 5580C26  LOCK BARREL KEY/SWITCH for deactivating passenger 'AIR BAG - R.R. - 7040A44  facia lh side cover - r r - 7040A45  facia rh side cover - r r - 7040A25  central facia trim - r r - 5540C18  headlamp/light cluster alignment correction motor switch - r+r - 7025A24  boot lid opening lever - r+r - 7040L42  sill plate connection of one front door (1), lh or rh - r r (left and right sides)  - 7040A04  facia lower trim-r r Drain the coolant fluid (refer to op.   5040A10  Air conditioning refrigerant CIRCUIT - Draining and Refilling ).  - 5010B24  under-facia air ducts r r - 5580C22  AIR BAG MODULE - Passenger side - R.R.
Before working on the Air Bag system follow the safety instructions for working on the system carefully (  See assembly 5580C   air bag system ).
 - 5530B10  battery - r+r - 1048A10  air cleaner filtering element - replace  - 5040C12  air conditioner housing - r r with facia disconnected1. Disconnect the electrical connection for the air intake actuator.

NameConnector
1Air intake actuator  N82 
2. Undo the bolts.3. Remove the cover.4. Move the seal.5. Undo the bolt.6. Disconnect the frost sensor from the evaporator.7. Remove the evaporator unit.
1. Undo the bolts.2. Remove the pipe connector (2a) and the lower seals (2b), then recover the expansion valve (2c) and also the upper seals (2d) and the plate (2e).
Refitting ( Removing ) Check that the expansion valve is not damaged or obstructed.Positin the plate, the new upper seals, the expansion valve, the new lower seals and the pipe connector on the evaporator pipes and fix them using the bolts.Position the frost sensor on the evaporator.Position the evaporator in the housing and tighten the bolt.Position the seal.Position the cover and fix it using the bolts.Connect the electrical connection. - 5040C12  air conditioner housing - r r with facia disconnected  - 1048A10  air cleaner filtering element - replace - 5530B10  battery - r+r - 5580C22  AIR BAG MODULE - Passenger side - R.R. - 5010B24  under-facia air ducts r r Repressurize the coolant fluid (refer to op.   5040A10  Air conditioning refrigerant CIRCUIT - Draining and Refilling ).  - 7040A04  facia lower trim-r r - 7040L42  sill plate connection of one front door (1), lh or rh - r r (left and right sides)  - 7025A24  boot lid opening lever - r+r - 5540C18  headlamp/light cluster alignment correction motor switch - r+r - 7040A25  central facia trim - r r - 7040A45  facia rh side cover - r r - 7040A44  facia lh side cover - r r - 5580C26  LOCK BARREL KEY/SWITCH for deactivating passenger 'AIR BAG - R.R. - 7040A37  fuse box cover - r r - 7040A96  facia glove compartment flap (1) lh or rh - r r (left and right sides)  - 7010M16  rear electric window enablement switch - r+r - 7065C42  ashtray (one) r+r - 7040A77  glass holder on facia trim - r r - 5570T80  car radio unit - r+r - 5560B10  analogue control panel - r+r - 7040A11  control panel lid - r + r - 7065C10  air conditioning control panel - r+r - 2125C24  gear lever knob - r + r - 7040A09  passenger air bag compartment cover - r r - 7040L20  tunnel trim - r r