2892148 - 7030B23 MOULDING/SUPPORT seal for SLIDING ROOF GLASS PANEL, Front or Rear - R.R.

Removing ( Refitting )  - 7045A10  l/h or r/h front seat (one) - r+r (Left and right).  - 7040H30  front pillar trim - r r (Left and right).  - 3380A44  handbrake/linkage protection - r+r - 7040H34  central pillar trim - r r (Left and right).  - 7040H42  rear pillar trim - r r (Left and right).  - 7040G40  load compartment light bulb holder - r r (only when removing rear sun-roof)  - 7040B18  l/h or r/h side trim (one) of luggage compartment/load platform - arrange (left and right side, only when removing rear sliding roof)  - 7040H33  glasses holder (1) lh or rh, on roof trim - r r (Left and right).  - 7065C34  l/h or r/h sun blind (one) - r+r (Left and right).  - 5580E22  Anti-theft device VOLUMETRIC SENSORS - R.R. after checking electrical circuit - 7040E50  front modular courtesy light unit - r+r - 7065C30  interior l/h or r/h grab handle (one) - r+r (all)  - 7040E17  lh or rh rear courtesy light - r r (Left and right).  - 7030B32  sliding roof decorative seal(1) front or rear - r r (front and rear)  - 7030B62  sliding roof control switch (1) front rear - r r (front and rear)  - 7030B20  sliding roof glass front or rear - r r (front or rear)  - 7030B11  sliding roof(assembly, 1 front or rear - r r ) (front or rear) 1. Undo the bolts securing the electric motor.2. Remove the electric motor.3. Undo the guide bolts.4. Remove the guides complete with traction cable.5. Undo the bolt.6. Remove the motor mounting complete with traction cable tubes.
1. If necessary, remove the seal (1a) from its seating, detaching it from the silicone glue (1b).
Refitting ( Removing ) 1. If the seal has been removed from the sunroof, carefully clean the seal seat on the sunroof with compressed air and degrease thoroughly using heptane.2. Carefully clean the bottom of the sea with compressed air and thoroughly degrease with heptane.3. Apply the appropriate silicone product along the entire perimeter.

TypeComponentNameQty.
3SiliconeSUNROOF GLASS SEALDOW CORNING 7091 Cap. 9.55719-
4. Position the seal in its seating.
Position the sunroof temporarily on the seal and check that the contact on the sunroof is correct.
Wait at least 5 hours before opening the sunroof.
Position the motor mounting complete with traction cable tubes, and secure it with the bolt. Fit the guides complete with traction cables and secure them with their bolts.
The electric motor is of the continuous cycle type, so no adjustment is required before fittiing.
Manually place the sunroof at the rear end-of-travel position and, in this position, fit the electric motor and fix it with the bolts. - 7030B11  sliding roof(assembly, 1 front or rear - r r ) (front or rear)  - 7030B20  sliding roof glass front or rear - r r (front or rear)  - 7030B62  sliding roof control switch (1) front rear - r r (front and rear)  - 7030B32  sliding roof decorative seal(1) front or rear - r r (front and rear)  - 7040E17  lh or rh rear courtesy light - r r (Left and right).  - 7065C30  interior l/h or r/h grab handle (one) - r+r (all)  - 7040E50  front modular courtesy light unit - r+r - 5580E22  Anti-theft device VOLUMETRIC SENSORS - R.R. after checking electrical circuit - 7065C34  l/h or r/h sun blind (one) - r+r (Left and right).  - 7040H33  glasses holder (1) lh or rh, on roof trim - r r (Left and right).  - 7040B18  l/h or r/h side trim (one) of luggage compartment/load platform - arrange (Left and right).  - 7040G40  load compartment light bulb holder - r r - 7040H42  rear pillar trim - r r (Left and right).  - 7040H34  central pillar trim - r r (Left and right).  - 3380A44  handbrake/linkage protection - r+r - 7040H30  front pillar trim - r r (Left and right). - 7050A10 rear seat - r+r (all)  - 7045A10  l/h or r/h front seat (one) - r+r (Left and right). Check that all the parts are fitted correctly and check the operation of removed electrical components.