2891728 - 4420D10 rear suspension axle - r+r includes bleeding

Removing ( Refitting ) Position the vehicle on the ramp.Loosen the handbrake lever adjustment nut. - 4450B13  rear wheels(2) r r . Raise the car. - 1076B20  rear exhaust silencer - r + r .  - 4420C10  rear suspension stabilizer bar - r+r . 1. Disconnect the handbrake cables (1a) from the connecting bracket (1b) and remove them from the mountings on the bodyshell (1c). 1. Remove the spring from the connectors between the rigid rear brake pipes and the flexible intermediate pipes.2. Separate the rigid pipes from the flexible pipes, undoing the connectors using the tool.

	Name	Country
-	Box wrench for brake fittings	1.856.132.000

Fit the tool for fixing the rear axle on a hydraulic jack.

	Name	Country
-	Mount	1.870.602.000

1. Position the hydraulic jack with the tool (1a) in the centre of the rigid rear axle and fix it using the two knobs (1b).

	Name	Country
1a	Mount	1.870.602.000

1. Undo the side bolts fixing the rigid rear axle to the bodyshell. Lower the hydraulic jack with the rigid rear axle and remove it. Refitting ( Removing )

Before refitting the rear suspension axle, check that there are no cracks, distortions or non alignment between the two side arms. If this is the case, replace it.

Reposition the rigid rear axle with the hydraulic jack.Tighten the side bolts fixing the rigid rear axle to the bodyshell to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	REAR RIGID AXLE	M12 x 1.25	10.6

Remove the hydraulic jack.Tighten the rigid pipes for the load proportioning valves to the flexible intermediate pipes, using the tool, to torque.

	Name	Country
-	Box wrench for brake fittings	1.856.132.000

	Fastening	Component	Ø	Value(daNm)
-	Connector	RIGID PIPE FRM LOAD PROPORT VALVE - HOSE	M10	1.4

Fit the spring on the connectors between the rigid brake pipes and the flexible intermediate pipes.Connect the handbrake cables to the connecting bracket and fit them on the mounting on the bodyshell. - 4420C10  rear suspension stabilizer bar - r+r .  - 1076B20  rear exhaust silencer - r + r . Lower the vehicle. - 3330A10  BRAKE FLUID - Check level and top up, if necessary. .  - 3330A18  front or rear hydraulic brake system - bleed .  - 4450B13  rear wheels(2) r r .  - 3380A04  handbrake - check travel . Remove the car from the ramps. Removing ( Refitting ) Position the vehicle on the ramp.Disconnect the battery negative terminal.

	Name	Connector
-	Battery	A1

Loosen the handbrake lever adjustment nut. - 4450B13  rear wheels(2) r r . Raise the car. - 1076B20  rear exhaust silencer - r + r . 1. Disconnect the handbrake cables (1a) from the bracket (1b). 1. Separate the rigid pipes from the flexible pipes, undoing the connectors using the special tool.

	Name	Country
-	Box wrench for brake fittings	1.856.132.000

Fit the tool for fixing the rear axle on a hydraulic jack.

	Name	Country
-	Mount	1.870.602.000

1. Position the hydraulic jack with the tool (1a) in the centre of the rigid rear axle and fix it using the two knobs (1b).

	Name	Country
1a	Mount	1.870.602.000

1. Undo the side bolts fixing the rigid rear axle to the bodyshell. Lower the hydraulic jack with the rigid rear axle and remove it. Refitting ( Removing ) Reposition the rigid rear axle with the hydraulic jack.Tighten the side bolts fixing the rigid rear axle to the bodyshell to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	REAR RIGID AXLE	M12 x 1.25	12.

Remove the hydraulic jack.Tighten the rigid brake pipes to the flexible intermediate pipes to torque using the tool.

	Name	Country
-	Box wrench for brake fittings	1.856.132.000

	Fastening	Component	Ø	Value(daNm)
-	Connector	RIGID PIPE FRM LOAD PROPORT VALVE - HOSE	M10	1.6

Connect the handbrake cables to the bracket. - 1076B20  rear exhaust silencer - r + rLower the vehicle. - 3330A10  BRAKE FLUID - Check level and top up, if necessary. - 3330A18  front or rear hydraulic brake system - bleed - 4450B13  rear wheels(2) r r - 3380A04  handbrake - check travel - 4450A40  rear wheel geometry - check using optical equipmentConnect the battery negative terminal.

	Name	Connector
-	Battery	A1

Remove the car from the ramps.