3024931 - 1020E10 oil seal cover (one) - l or r - on counter-rotating shafts - r + r and replace seals

Removing ( Refitting ) Position the vehicle on the ramp.Ensure that the ignition key is in the stop OFF, then disconnect the battery negative terminal.

	Name	Connector
-	Battery	A1B

Proceed with the removal  - 4450B10  Front WHEEL (one) - R.R. (Right side). Proceed with the removal  - 7055B54  under-engine guard - r r . Proceed with the removal  - 7055B64  Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side). Proceed with the removal  - 1092G10  single engine belt r r . Proceed with the removal  - 1092A10  Crankshaft services PULLEY - R.R. . Proceed with the removal  - 1092G20  engine component single belt fixed tensioner - one - r + r . Proceed with the removal  - 1092G14  engine component single belt mobile tensioner - r + r . Proceed with the removal  - 1032D12  timing system protective cover(s) - r + r . Proceed with the removal  - 1092E10  counter-rotating shaft drive toothed belt - r + r . Proceed with the removal  - 1016A40  ignition coil cover on cylinder head- r+r . Proceed with the removal  - 5510C14  ignition coil/s - r+r . Proceed with the removal  - 1016A20  single cam cover - r + r and replace gasket . Proceed with the removal  - 1032B10  toothed timing belt - r + r for timing adjustment or replacement . For the left counter-balance shaft cover, proceed as follows.1. Undo the bolt (1a) for the left counter-balance shaft pulley using the tool (1b) for counter-torque.

	Name	Country
1b	Counter-torque	1.820.286.000

2. Remove the left counter-balance shaft pulley. 1. Undo the bolt (1a) and remove the fixed timing belt tensioner (1b). 1. Undo the nut (1a) and remove the counter-balance shaft drive belt tensioner (1b). 1. Undo the bolts (1a) and remove the left counter-balance shaft cover (1b) complete with oil seal and O-Ring. For the right counter-balance shaft cover, proceed as follows.1. Undo the nut (1a) and remove the timing drive belt moving tensioner (1b). Undo the bolt (1a) for the right counter-balance shaft pulley using the tool (1b) for counter-torque.

	Name	Country
1b	Counter-torque	1.820.286.000

2. Remove the right counter-balance shaft pulley. 1. Undo the bolts (1a) and remove the right counter-balance shaft cover (1b), complete with oil seal and O-Ring. Refitting ( Removing ) For the right counter-balance shaft cover, proceed as follows.1. Place the right counter-balance shaft cover (1a), complete with oil seal and new O-Ring back in its housing, then secure it by tightening the bolts (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	COUNTER ROTATING SHAFT FRONT COVER	M6	(Engine crankcase side) 0.8 ÷ 1.0

1. Place the right counter-balance shaft pulley (1a) back in its housing and secure it by tightening the bolt (1b) to the recommended torque using the tool (1c) for counter-torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	COUNTER-ROTATING SHAFT PULLEY	M10	(Counter balance shaft side) 4.5 ÷ 5.5

	Name	Country
1c	Counter-torque	1.820.286.000

Fit the timing belt mobile tensioner and fix it using the nut without tightening it.For the left counter-balance shaft cover, proceed as follows.1. Place the left counter-balance shaft cover (1a), complete with oil seal and new O-Ring, back in its housing, then secure it by tightening the bolts (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	COUNTER ROTATING SHAFT FRONT COVER	M6	(Engine crankcase side) 0.8 ÷ 1.0

Place the counter-balance shaft belt tensioner back in its housing and secure it without tightening the nut.1. Place the timing fixed tensioner (1a) back in its housing and secure it by tightening the bolt (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	FIXED TENSIONER	M8	2.3 ÷ 2.8

1. Place the left counter-balance shaft pulley (1a) back in its housing and secure it by tightening the bolt (1b) to the recommended torque using the tool (1c) for counter-torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	COUNTER-ROTATING SHAFT PULLEY	M10	(Counter balance shaft side) 4.5 ÷ 5.5

	Name	Country
1c	Counter-torque	1.820.286.000

PROCEED as follows for both counter-balance shaft coversProceed with the refitting  - 1032B10  toothed timing belt - r + r for timing adjustment or replacement .Proceed with the refitting  - 1016A20  single cam cover - r + r and replace gasket .Proceed with the refitting  - 5510C14  ignition coil/s - r+r .Proceed with the refitting  - 1016A40  ignition coil cover on cylinder head- r+r .Proceed with the refitting  - 1092E10  counter-rotating shaft drive toothed belt - r + r .Proceed with the refitting  - 1032D12  timing system protective cover(s) - r + r .Proceed with the refitting  - 1092G14  engine component single belt mobile tensioner - r + r .Proceed with the refitting  - 1092G20  engine component single belt fixed tensioner - one - r + r .Proceed with the refitting  - 1092A10  Crankshaft services PULLEY - R.R. .Proceed with the refitting  - 1092G10  single engine belt r r .Proceed with the refitting  - 7055B64  Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side).Proceed with the refitting  - 7055B54  under-engine guard - r r .Proceed with the refitting  - 4450B10  Front WHEEL (one) - R.R. (Right side).Connect the battery terminal (-).Remove the car from the ramp.