3024804 - 1036C10 camshaft in cylinder head - r r on vehicle

Removing ( Refitting ) Position the vehicle on the ramp.Ensure that the ignition key is in the OFF postition, then disconnect the battery negative terminal.

	Name	Connector
-	Battery	A1B

Proceed with the removal  - 4450B10  Front WHEEL (one) - R.R. (Right side). Proceed with the removal  - 7055B54  under-engine guard - r r . Proceed with the removal  - 7055B64  Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side). Proceed with the removal  - 1092G10  single engine belt r r . Proceed with the removal  - 1092A10  Crankshaft services PULLEY - R.R. . Proceed with the removal  - 1092G20  engine component single belt fixed tensioner - one - r + r . Proceed with the removal  - 1092G14  engine component single belt mobile tensioner - r + r . Proceed with the removal  - 1032D12  timing system protective cover(s) - r + r . Proceed with the removal  - 1092E10  counter-rotating shaft drive toothed belt - r + r . Proceed with the removal  - 1016A40  ignition coil cover on cylinder head- r+r . Proceed with the removal  - 5510C14  ignition coil/s - r+r . Proceed with the removal  - 1016A20  single cam cover - r + r and replace gasket . Proceed with the removal  - 1032B10  toothed timing belt - r + r for timing adjustment or replacement . Proceed with the removal - 1032B52  toothed driven pulley (one) - r + r (intake side and exhaust side)1. Undo bolts (1a) and move cam angle sensor (1b).2. Undo the bolts (2a) and remove the camshaft caps (2b).3. Remove the upper bearing shell for the front camshaft support, inlet side.4. Remove the camshafts (4a) and the front camshaft oil seals (4b).5. Remove the lower bearing shell for the front camshaft support, inlet side. Refitting ( Removing ) Place the inlet side camshaft front support lower half-bearing back in its housing.Place the camshafts back in their housings.Place the inlet side camshaft front support upper half-bearing back in its housing.Fit the camshaft caps and fix them tightening the bolts to the recommended torque.

Do not fit the 3rd camshaft cap because the engine timing adjustment templates are fitted in its place.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	CAMSHAFT CAPS/	M7	(Cylinder head side) 1.4 ÷ 1.7

1. Fit the front camshaft oil seal, exhaust side (1a) using the tool (1b).

	Name	Country
1b	Fitting tool	1.821.228.000

1. Fit the front camshaft oil seal, inlet side (1a) using the tool (1b).

	Name	Country
1b	Fitting tool	1.821.251.000

Place the cam angle sensor back in its housing and fix it using the bolt.Proceed with the refitting  - 1032B52  toothed driven pulley (one) - r + r (intake side and exhaust side).Proceed with the refitting  - 1032B10  toothed timing belt - r + r for timing adjustment or replacement .Proceed with the refitting  - 1016A20  single cam cover - r + r and replace gasket .Proceed with the refitting  - 5510C14  ignition coil/s - r+r .Proceed with the refitting  - 1016A40  ignition coil cover on cylinder head- r+r .Proceed with the refitting  - 1092E10  counter-rotating shaft drive toothed belt - r + r .Proceed with the refitting  - 1032D12  timing system protective cover(s) - r + r .Proceed with the refitting  - 1092G14  engine component single belt mobile tensioner - r + r .Proceed with the refitting  - 1092G20  engine component single belt fixed tensioner - one - r + r .Proceed with the refitting  - 1092A10  Crankshaft services PULLEY - R.R. .Proceed with the refitting  - 1092G10  single engine belt r r .Proceed with the refitting  - 7055B64  Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side).Proceed with the refitting  - 7055B54  under-engine guard - r r .Proceed with the refitting  - 4450B10  Front WHEEL (one) - R.R. (Right side).Connect the battery terminal (-).Remove the car from the ramp.