3340A12 A'B.S. SYSTEM. - ELECTRONIC AND HYDRAULIC CONTROL UNIT R.R. - Alfa - 147 - eLearn

3025245 - 3340A12 A'B.S. system. - electronic and hydraulic CONTROL UNIT R.R.

) Position the vehicle on the ramp.Proceed with removal - 5530B10 battery - r+r . Proceed with removal - 5530B52 Battery DRIP TRAY/SUPPORT - R.R. . Proceed with removal - 4450B02 left front wheel r r . Proceed with removal - 3330C30 brake fluid reservoir - r + r and wash inside . 1. Disconnect the electrical connection from the A.B.S. hydraulic and electronic control unit.

	Name	Connector
1	ABS control unit	M50

2. Undo the connectors (2a) and (2b) and remove the rigid pipes from the master cylinder to the ABS hydraulic unit (2c).3. Undo the connectors (3a) and disconnect the rigid pipes from the hydraulic control unit to the brake calipers (3b), hydraulic unit side.4. Release the ABS pipes from the attachments.

1. Disconnect the electrical connection for the VDC system pressure sensor.

	Name	Connector
1	Pressure sensor (VDC)	K72

2. Remove the stops (2a) and remove the ABS hydraulic and electronic unit (2b).

Refitting ( Removing

) .

The letters indicating to which caliper and to which brake pump outlet they should be connected are stamped on the control unit at each outlet.RR = to the right rear brake (pipe marked with a light blue coloured band) LR = to the left rear brake (pipe marked with a green coloured band) RF = to the right front caliper (pipe marked with a yellow coloured band) LF = to the left front caliper (pipe marked with a white coloured band) MC1 = from the main circuit/flange side pump (pipe marked with a black or pink coloured band when the pipe polyamide resin is black) MC2 = from the secondary circuit/front pump (pipe marked with a brown coloured band).

Place the ABS hydraulic and electronic unit back in its housing and secure it with its attachments. Connect the electrical connection to the VDC system pressure sensor.1. Connect the rigid pipes from the hydraulic unit to the brake calipers (1a), hydraulic unit side, and tighten the connectors (1b) to the specified torque.

	Fastening	Component	Ø	Value(daNm)
1b	Connector	RIGID CENTRE BRAKE PIPES../	M10/M12	(Control unit side) 1.4 ÷ 1.8

2. Secure the rigid pipes from the hydraulic unit to the brake calipers to the attachments. 3. Place in their seatings the rigid pipes from the master cylinder to the ABS hydraulic unit (3a) and tighten the connectors (3b) and (3c) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
3b	Connector	PIPE FROM PUMP TO HYDRAULIC CONTROL UNIT	M12	(Master cylinder side) 1.4 ÷ 1.8

	Fastening	Component	Ø	Value(daNm)
3c	Connector	PIPE FROM PUMP TO HYDRAULIC CONTROL UNIT	M12	(A.B.S.) control unit side 1.4 ÷ 1.8

4. Connect the electrical connection to the A.B.S. hydraulic and electronic control unit.

Proceed with refitting - 3330C30 brake fluid reservoir - r + r and wash inside .Proceed with refitting - 5530B52 Battery DRIP TRAY/SUPPORT - R.R. .Proceed with refitting - 5530B10 battery - r+r .Top up the brake-clutch fluid level - 0010T64 brake and or clutch fluid check level and top up as necessary .Bleed the air from the hydraulic braking system - 0010T65 hydraulic brake system bleed air .Proceed with refitting - 4450B02 left front wheel r r .Remove the car from the ramps.