3025418 - 5040A50 pipe from compressor to air conditioner condenser - r+r

Follow the safety instructions ( See subassembly 5040   AIR CONDITIONING CASING AND COMPONENTS ).

Removing ( Refitting ) Drain the coolant ( - 5040A10  Air conditioning refrigerant CIRCUIT - Draining and Refilling ). - 7055B54  under-engine guard - r r - 7210E10  R.R. FRONT BUMPER1. Undo the bolt fixing the pipe to the condenser.2. Disconnect the pipe connector.

Seal the disconnected connectors, using suitable plugs, to prevent humidity and impurities from entering the system.

1. Undo the bolt fixing the pipe to the compressor.2. Disconnect the nut fixing the intermediate coupling.3. Disconnect the pipe connectors.

Seal the disconnected connectors, using suitable plugs, to prevent humidity and impurities from entering the system.

4. Recover the pipe. Refitting ( Removing ) Check that the pipe is not damaged or cracked.Reposition the pipe.

Replace the O-rings for the connectors.

Only use green coloured seals, resistant to R134A coolant fluid.

Lubricate the thread of the connectors using anti-freeze.

Connect the pipe connectors and tighten the bolts and the nut.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	COOLANT SYSTEM FITTINGS	M6	0.9

	Fastening	Component	Ø	Value(daNm)
-	Nut	COOLANT SYSTEM FITTINGS	M6	0.9

 - 7210E10  R.R. FRONT BUMPER - 7055B54  under-engine guard - r rRepressurize using coolant fluid ( - 5040A10  Air conditioning refrigerant CIRCUIT - Draining and Refilling ). Removing ( Refitting ) Observe the following precaution.

Follow the safety instructions ( See subassembly 5040   AIR CONDITIONING CASING AND COMPONENTS ).

Drain the coolant ( - 0010T84  coolant for air conditioning system dehydrate and recharge ). - 7055B54  under-engine guard - r r - 7055B64  Engine compartment DUST shield in front wheel arch (one), left or right - R.R. - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. - 7210E10  R.R. FRONT BUMPER1. Undo the nut fastening the intermediate coupling for the pipe from the climate control casing to the compressor.2. Disconnect the intermediate coupling.

Seal the housing for the drier filter cartridge using a suitable plug to prevent dampness and impurities from entering the system.

1. Working in front of the right front wheel, release the buttons retaining the air duct using the special tool.

	Name	Country
1	Scraper blade	1.823.015.000

2. Undo the bolts fixing the air duct.3. Remove the air duct. 1. Undo the bolt and disconnect the connector (1a) for the pipe from the condenser (1b). 1. Working under the engine, undo the bolt and disconnect the connector (1a) for the pipe from the compressor (1b).2. Remove the pipe Refitting ( Removing ) Check that the pipe is not damaged or cracked.Position the pipe.

Replace the O-rings for the connectors. Only use green coloured seals, resistant to R134A refrigerant. Lubricate the thread of the connectors using anti-freeze.

Connect the pipe connectors and tighten the bolts and the nut.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	COOLANT SYSTEM FITTINGS	M6	0.9

	Fastening	Component	Ø	Value(daNm)
-	Nut	COOLANT SYSTEM FITTINGS	M6	0.9

Fit the air duct in place and secure it using the bolts.Engage the air duct retaining buttons. - 7210E10  R.R. FRONT BUMPER - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. - 7055B64  Engine compartment DUST shield in front wheel arch (one), left or right - R.R. - 7055B54  under-engine guard - r rRepressurize using coolant fluid ( - 0010T84  coolant for air conditioning system dehydrate and recharge ).