3025260 - 3340B56 RIGID PIPE from hydraulic CONTROL UNIT to RIGHT FRONT BRAKE - R.R.

Removing ( Refitting ) Position the vehicle on the ramp.Proceed with removal  - 4450B10  Front WHEEL (one) - R.R. .Remove the protective cap on the brake caliper bleed valve.Connect the collection system (pipe and reservoir) to the bleed valve on the brake caliper. Operate the brake pedal until the brake-clutch fluid reservoir is empty. 1. Undo the connectors (1a) and (1b) and remove the rigid pipes from the master cylinder to the ABS hydraulic unit (1c). 2. Undo the connector (2a) and disconnect the rigid pipe from the hydraulic unit to the front right brake (2b), hydraulic unit side. Release the rigid pipe from the hydraulic unit to the front right brake from the attachment on the control unit mounting.
Proceed with removal  - 5530B10  battery - r+r .Proceed with removal  - 5530B52  Battery DRIP TRAY/SUPPORT - R.R. .Drain the air conditioner coolant circuit  - 5040A10  Air conditioning refrigerant CIRCUIT - Draining and Refilling .Proceed with removal  - 7055B54  under-engine guard - r r .Proceed with removal  - 7055B64  Engine compartment DUST shield in front wheel arch (one), left or right - R.R. .Proceed with removal  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. .Proceed with removal  - 7210E10  R.R. FRONT BUMPER .Proceed with the removal  - 5540B76  Front LIGHT CLUSTER with fog light (one), left or right - R.R. with interfering components removed (Right and left sides).Proceed with removal  - 7025A34  bonnet lid lock (one) - r+r or repair .Proceed with removal  - 7210A15  R.R. HEADLAMP HOUSING/FRONT WING CROSSMEMBER .Proceed with removal  - 1076B82  left exhasust pipe between catalytic preconverter and converter r r .Proceed with removal  - 1076B84  right exhaust pipe between caralytic preconverter and converter r r .Proceed with removal  - 1080B39  right catalytic preconverter r r or replace cylinder head gasket .Proceed with removal  - 1008A44  rear rigid mount - r r .Proceed with removal  - 4130A10  power steering box - r+r - check tow-in if necessary separately - includes bleeding .1. Release the rigid pipe from the hydraulic unit to the front right brake from the attachments on the engine compartment bulkhead.
1. Undo the connector (1a) and disconnect the rigid pipe from the hydraulic unit to the front right brake (1b), flexible pipe side.2. Release the rigid pipe from the hydraulic control unit to the front right brake from the attachment in the wheelarch.
1. Undo the bolts (1a) and remove the protection (1b) for the fuel supply pipe and fuel vapour recovery pipe. 2. Release the fuel supply pipe and fuel vapour recovery pipe from the attachments on the underbody.
1. Working in the wheel compartment, remove the rigid pipe from the hydraulic unit to the front right brake.
Refitting ( Removing ) Place the rigid pipe from the hydraulic control unit to the right front brake back in its housing.Secure the fuel supply pipe and fuel vapour recovery pipe to the attachments on the underbody.Refit in its seating the protection for the fuel supply pipe and fuel vapour recovery pipe and fix it with the bolts. Fix the rigid pipe from the hydraulic control unit to the front right brake to the attachment in the wheelarch. 1. Connect the rigid pipe from the hydraulic control unit to the front right brake (1a), flexible pipe side, and tighten the connector (1b) to the recommended torque.

FasteningComponentØValue(daNm)
1bConnectorPIPE FROM CONTROL UNIT TO FRONT BRAKESM10(Flexible pipe side) 1.4 ÷ 1.8
Secure the rigid pipe from the hydraulic unit to the front right brake to the attachments on the engine compartment bulkhead.Proceed with refitting  - 4130A10  power steering box - r+r - check tow-in if necessary separately - includes bleeding .Proceed with refitting  - 1008A44  rear rigid mount - r r .Proceed with refitting  - 1080B39  right catalytic preconverter r r or replace cylinder head gasket .Proceed with refitting  - 1076B84  right exhaust pipe between caralytic preconverter and converter r r .Proceed with refitting  - 1076B82  left exhasust pipe between catalytic preconverter and converter r r .Proceed with refitting  - 7210A15  R.R. HEADLAMP HOUSING/FRONT WING CROSSMEMBER .Proceed with refitting  - 7025A34  bonnet lid lock (one) - r+r or repair .Proceed with the refitting  - 5540B76  Front LIGHT CLUSTER with fog light (one), left or right - R.R. with interfering components removed (Right and left sides).Proceed with refitting  - 7210E10  R.R. FRONT BUMPER .Proceed with refitting  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. .Proceed with refitting  - 7055B64  Engine compartment DUST shield in front wheel arch (one), left or right - R.R. .Proceed with refitting  - 7055B54  under-engine guard - r r .Fill the air conditioner coolant circuit  - 5040A10  Air conditioning refrigerant CIRCUIT - Draining and Refilling .Proceed with refitting  - 5530B52  Battery DRIP TRAY/SUPPORT - R.R. .Proceed with refitting  - 5530B10  battery - r+r .Secure the rigid pipe from the hydraulic unit to the front right brake to the attachment on the control unit mounting. 1. Connect the rigid pipe from the hydraulic unit to the front right brake (1a), hydraulic unit side, and tighten the connector (1b) to the specified torque.

FasteningComponentØValue(daNm)
1bConnectorPIPE FROM CONTROL UNIT TO FRONT BRAKESM10(A.B.S.) control unit side 1.4 ÷ 1.8
2. Place the rigid pipes from the master cylinder to the ABS hydraulic unit (2a) in their seatings, and tighten the connectors (2b) and (2c) to the recommended torque.

FasteningComponentØValue(daNm)
2bConnectorPIPE FROM PUMP TO HYDRAULIC CONTROL UNITM12(Master cylinder side) 1.4 ÷ 1.8

FasteningComponentØValue(daNm)
2cConnectorPIPE FROM PUMP TO HYDRAULIC CONTROL UNITM12(A.B.S.) control unit side 1.4 ÷ 1.8
Top up the brake-clutch fluid level  - 0010T64  brake and or clutch fluid check level and top up as necessary .Bleed the air from the hydraulic braking system  - 0010T65  hydraulic brake system bleed air .Remove the car from the ramps.