3025327 - 4410c10 front suspension stabilizer bar - r+r - check wheel geometry separately

Removing ( Refitting ) Position the vehicle on the ramp.Ensure that the ignition key is in the OFF position, then disconnect the negative battery terminal (-).

	Name	Connector
-	Battery	A1B

Proceed with removal  - 4450B12  front or rear wheels (two) - r+r . Proceed with removal  - 7055B54  under-engine guard - r r . Proceed with removal  - 1076B82  left exhasust pipe between catalytic preconverter and converter r r .Proceed with removal  - 1076B84  right exhaust pipe between caralytic preconverter and converter r r . Only for the GTA version, unscrew the bolts and remove the underbody reinforcements.1. Undo the bolts securing the antiroll bar to the front suspension crossmember.2. Undo the bolts (2a) and the nuts (2b) fixing the gear lever and handbrake lever mount.3. Undo the bolts fixing the power assisted steering box to the front suspension crossmember.4. Fit tool (4a) with hydraulic jack (4b) to support the front suspensiojn beam.

	Name	Country
4a	Flange	1.860.978.000

5. Undo the rear bolts fixing the front suspension crossmember to the bodyshell.6. Undo the side bolts fixing the front suspension crossmember to the bodyshell.Lower the hydraulic jack with the front suspension beam as necessary. 1. Undo the nuts (1a) and remove the rear suspension anti-roll bar joints (1b). Lower the front suspension beam further using the hydraulic jack. Leave it secured only to the lower wisbhones.1. Remove the front suspension anti-roll bar. Refitting ( Removing ) Replace the front suspension anti-roll bar in its housing.Raise the front suspension beam as necessary using the hydraulic jack.1. Place the front suspension anti-roll bar joints (1a) back in their housings and secure by tightening nuts(1b) and (1c) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Nut	FRONT ANTI-ROLL BAR JOINTS	M10	(Front shock absorber fork side) 4.1 ÷ 5.0

	Fastening	Component	Ø	Value(daNm)
1c	Nut	FRONT ANTI-ROLL BAR JOINTS	M10	(Anti-roll bar side) 4.5 ÷ 5.5

Fully raise the front suspension beam using the hydaulic jack.1. Tighten the side bolts securing the front suspension crossmember to the bodyshell to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Side bolt	ENGINE OR ROD ANCHORAGE BEAM	M12	(Bodyshell side) 10.8 ÷ 13.2

2. Tighten the rear bolts securing the front suspension crossmember to the bodyshell to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2	Rear bolts	ENGINE OR ROD ANCHORAGE BEAM	M12	(Bodyshell side) 10.8 ÷ 13.2

	Fastening	Component	Ø	Value(daNm)
2	Rear bolt	ENGINE OR ROD ANCHORAGE BEAM	M10	(Bodyshell side) 7.2 ÷ 8.8

3. Remove the hydraulic jack (3a) and tool (3b) supporting the front suspension crossmember.

	Name	Country
3b	Flange	1.860.978.000

4. Tighten the bolts securing the power steering box to the front suspension crossmember to the specified torque.

	Fastening	Component	Ø	Value(daNm)
4	Bolt	POWER STEERING BOX	M14	(Front suspension crossmember side) 11.7 ÷ 14.3

5. Tighten nuts (5a) and bolts (5b) securing the gearlever and handbrake lever mount.6. Tighten the bolts securing the antiroll bar to the front suspension crossmember to the specified torque.

	Fastening	Component	Ø	Value(daNm)
6	Bolt	FRONT ANTI-ROLL BAR	M8	(Front suspension crossmember side) 3.6 ÷ 4.4

Only on the GTA version, refit the underbody reinforcements in their seats and secure the bolts. Proceed with refitting  - 1008A44  rear rigid mount - r r . Proceed with refitting  - 1076B84  right exhaust pipe between caralytic preconverter and converter r r .Proceed with refitting  - 1076B82  left exhasust pipe between catalytic preconverter and converter r r . Proceed with refitting  - 7055B54  under-engine guard - r r . Connect the negative (-) battery terminal.Remove the car from the ramps.It is advisable to check the wheel alignment  - 4450A10  front wheel geometry - check using optical equipment - includes front wheel tow-in adjustment if necessary .