3363335 - 7035B12 Tailgate rearscreen (bonded type) WINDOW GLASS - R.R. - Includes. cleaning edges of glass and housing in tailgate

Removing ( Refitting )  - 5530B56  BATTERY DRIP TRAY COVER - R.R.Disconnect the battery negative terminal. - 7015A04  tailgate interior panel - r+r - 7015A58  internal tailgate moulding (one) - r+r - 5050C34  rear wiper arm with blade - r+r - 5050C42  rear wiper motor - r+rDisconnect and remove the parcel shelf.Disconnect the electrical connections for the heated rear window.

	Name	Connector
-	Heated rear windscreen	P55

Apply adhesive tape to protect the top and bottom edges of the bodywork.The bead of sealant for the rearscreen can be cut using either harmonic wire or the vibrating knife; both methods are described below.To cut the bead using harmonic wire, proceed as follows.1. Cut a section of harmonic wire about 50 cm long then, using pliers, insert one end (1a) of the harmonic wire through the bead of sealant (1b) which secures the window (1c). 2. Secure one end of the wire to the special retaining tool (2a), inside the vehicle, and the other end to the traction handle (2b), outside the vehicle. 1. The operator inside the vehicle should keep the end of the tool (1a) pressed against the bead of sealant (1b) about 30 cm away from the point where the wire passes, whilst the other operator, outside the vehicle, should pull the handle (1c), following the surround of the windscreen. 2. Whilst cutting the rearscreen side centring pins have to be broken. To cut the bead using the vibrating knife, proceed as described below.1. Use the vibrating knife (1a), with blade (1b), and cut the bead of sealant along the entire preimeter of the rear window.

Whilst cutting the rearscreen side centring pins have to be broken.

1. After having cut the entire bead of sealant, fit the suction pads to the rearscreen and remove it.Rest the rearscreen on a supporting stand. Refitting ( Removing ) Using a suitable tool, cut and smooth off the bead of sealant in the rear window frame, so as to leave a thickness of between 0.25 and 1 mm, without scratching the paintwork.

The sealant left in the housing will act as a backing for the new bond.

Clean the rear window seating carefully with compressed air and degrease thoroughly with heptane.If glueing takes place 60 minutes after cutting and smoothing the bead of sealant, treat the sealant surface with the specific activator and wait 15 minutes before fixing the rearscreen.

	Type	Component	Name	Qty.
-	PRIMER	TAIL-GATE GLASS SEALING STRIP	-	-

If necessary touch up the paintwork. If the same windscreen is being reused.  - 7035B26  rear window glass clean enges and sand small abrasionsIf this is not the case, use a new windscreen and proceed as described below.1. Fit locating pins.2. Degrease the screen printed area around the edge of the new window.3. Apply glass adhesion promoter (primer) (3b) to the screen printed area round the outside using applicator (3a) provided in the kit.

Wait for 15 minutes before carrying out the next operation to give the primer thinner time to evaporate.

Remove the adhesive tape from the edges of the bodywork, along the top and bottom perimeter of the rear window frame.1. Test fit the rear window and check that it is centred properly. Use an air gun to extrude a bead of sealant as evenly as possible along the perimeter of the rear window.

	Type	Component	Name	Qty.
-	Product n° 71711976	TAIL-GATE GLASS SEALING STRIP	-	-

Begin applying the sealant from the middle of the lower edge and continue without breaks around the entire edge of the window.

1. With the assistance of a second operator, fit the rear window in its seating immediately after applying the sealant and bed it in place.2. Fit the belt (2a) and adjust the tension to apply uniform pressure over the entire back window in order to ensure a correct match between window (2b), sealant (2c) and rearscreen housing (2d). Connect the electrical connections for the heated rear windscreen.

	Name	Connector
-	Heated rear windscreen	P55

Fit the parcel shelf. - 5050C42  rear wiper motor - r+r - 5050C34  rear wiper arm with blade - r+r - 7015A58  internal tailgate moulding (one) - r+r - 7015A04  tailgate interior panel - r+rConnect the battery negative terminal. - 5530B56  BATTERY DRIP TRAY COVER - R.R.