3362532 - 1028H11 PISTON CONNECTING ROD SET - R.R. FOR VERSIONS WITH AIR CONDITIONING

Removing ( Refitting ) Position the vehicle on a lift.    1016A40 COPERCHIO BOBINE accensione su testa cilindri - S.R.Op. 5040A10 AIR CONDITIONING REFRIGERANT CIRCUIT - DRYING AND REPRESSURIZING    Op. 5530B56 BATTERY DRIP TRAY COVER - R.R.Disconnect the negative battery terminal.    1048A28 DISPOSITIVO RISUONATORE circuito aria in depressione - S.R.    1048A32 MANICOTTO da filtro aria a collettore aspirazione - S.R.    Op. 1048A23 COLD AIR INTAKE FOR AIR FILTER - R.R    4450B10 RUOTA (una) anteriore - S.R.    Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.    7055B42 PASSARUOTA supplementare ANTERIORE (uno), sx o dx - S.R.    Op. 1088B10 ENGINE COOLANT SUPPLY RESERVOIR - R.R.    Op. 5510C14 IGNITION COIL/S - R+R    Op. 1016A20 SINGLE TAPPET COVER -R.R AND REPLACE GASKETOp. 1092B40 AIR CONDITIONING COMPRESSOR/ALTERNATOR DRIVE BELT - R + R    Op. 1008A46 POWER UNIT RIGID SUPPORT - TIMING SIDE - R.R.    Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R    Op. 1032B14 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT VERSIONS WITH AIR CONDITIONER    1016B12 TESTA SUPERIORE UNICA - S.R. a cinghia distribuzione staccata - Sost. guarnizione    1076B50 TUBAZIONE di scarico attacco al motore/collettore - S.R.    Op. 1020A26 CRANKCASE SUMP - R.R CLEAN MATING SURFACES AND APPLY SEALANT FOR VEHICLES WITH AIR CONDITIONINGRotate the crankshaft until cylinder 1 is at B.D.C.1. Undo the bolts (1a) and remove the connecting rod caps (1b) complete with lower half-bearings (1c) for cylinders 1 and 4.
1. Withdraw and remove the 1st and 4th cylinder pistons (1a) with connecting rods (1b) and upper connecting rod half bearings.
Work in the same way to remove the pistons and connecting rods for cylinders 2 and 3 rotating the crankshaft through 180 degrees. Refitting ( Removing ) 1. Fit the 2nd and 3rd cylinder pistons (1a) with connecting rods (1b) and upper connecting rod half bearings (1c) using a suitable tool.
The pistons and connecting rods are fitted in the cylinder block/crankcase with the large references (for the inlet valves) on the piston crown facing the inlet side.
1. Place the connecting rod caps (1a) for cylinders 2 and 3 in their seats complete with lower half-bearings (1b) and secure them by tightening the bolts (1c) to the recommended torque using the angular rotation tool.
Fit the connecting rods so that the number stamped on each rod faces towardt he same side as the number stamped on the connecting rods.
DescriptionCode
-Torque wrench1.860.942.000
FasteningComponentØ  Value(daNm)
1cBoltCONNECTING ROD CAPSM92.5 + 60°
    Op. 1020A26 CRANKCASE SUMP - R.R CLEAN MATING SURFACES AND APPLY SEALANT FOR VEHICLES WITH AIR CONDITIONING    1076B50 TUBAZIONE di scarico attacco al motore/collettore - S.R.    Op. 1016C10 SINGLE CYLINDER HEAD - R.R. AND REPLACE GASKET    Op. 1032B14 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT VERSIONS WITH AIR CONDITIONER    Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R    Op. 1008A46 POWER UNIT RIGID SUPPORT - TIMING SIDE - R.R.Op. 1092B40 AIR CONDITIONING COMPRESSOR/ALTERNATOR DRIVE BELT - R + R    Op. 1016A20 SINGLE TAPPET COVER -R.R AND REPLACE GASKET    Op. 5510C14 IGNITION COIL/S - R+R    Op. 1088B10 ENGINE COOLANT SUPPLY RESERVOIR - R.R.    7055B42 PASSARUOTA supplementare ANTERIORE (uno), sx o dx - S.R.    Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.    4450B10 RUOTA (una) anteriore - S.R.    Op. 1048A23 COLD AIR INTAKE FOR AIR FILTER - R.R    1048A32 MANICOTTO da filtro aria a collettore aspirazione - S.R.    1048A28 DISPOSITIVO RISUONATORE circuito aria in depressione - S.R.Connect the negative battery terminal.    Op. 5530B56 BATTERY DRIP TRAY COVER - R.R.Op. 5040A10 AIR CONDITIONING REFRIGERANT CIRCUIT - DRYING AND REPRESSURIZING    1016A40 COPERCHIO BOBINE accensione su testa cilindri - S.R.    Op. 0010T21 ENGINE COOLANT - CHECK DENSITY AND CHANGE, IF NECESSARYRemove the vehicle from the lift.