3362589 - 1036C10 CAMSHAFTS IN CAMSHAFT HOUSING - R.R - INCLUDES CAMSHAFT HOUSING REPLACEMENT, IF NECESSARY

Removing ( Refitting ) Position the vehicle on a lift.    1016A40 COPERCHIO BOBINE accensione su testa cilindri - S.R.    Op. 5530B56 BATTERY DRIP TRAY COVER - R.R.Disconnect the negative battery terminal.    1048A28 DISPOSITIVO RISUONATORE circuito aria in depressione - S.R.    1048A32 MANICOTTO da filtro aria a collettore aspirazione - S.R.    Op. 1048A23 COLD AIR INTAKE FOR AIR FILTER - R.R    4450B10 RUOTA (una) anteriore - S.R.    Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.    7055B42 PASSARUOTA supplementare ANTERIORE (uno), sx o dx - S.R.    Op. 1088B10 ENGINE COOLANT SUPPLY RESERVOIR - R.R.    Op. 5510C14 IGNITION COIL/S - R+R    Op. 1016A20 SINGLE TAPPET COVER -R.R AND REPLACE GASKET    Op. 1008A46 POWER UNIT RIGID SUPPORT - TIMING SIDE - R.R.    Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R    Op. 1032B14 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT VERSIONS WITH AIR CONDITIONER1. Undo the bolts (1a) using the tool (1b) for counter-torque and remove the inlet side driven toothed pulley.
DescriptionCode
1bCounter-torque1.860.856.000
2. Undo the bolt (2a) using the tools (2b) and (2c) for counter-torque, then remove the exhaust side driven toothed pulley.
DescriptionCode
2bSupport for counter-torque1.860.831.000
DescriptionCode
2cCounter-torque1.860.848.000
1. Undo the bolts (1a) and move the cam angle sensor (1b) away from the cylinder head.2. Undo the bolts (2a) and remove the camshaft caps (2b).3. Remove the inlet side camshaft front supper upper half-bearing.4. Remove the camshafts.5. Remove the camshaft front support lower half-bearing.6. Remove the camshaft front oil seals.
Refitting ( Removing ) Place the inlet side camshaft front support lower half-bearing in its housing.Place the camshafts in their housings.Place the inlet side camshaft front support upper half-bearing in its housing.Fit the camshaft caps except those for the third support (in place of which the timing templates should be fitted) and secure them tightening the bolts to the recommended torque.
FasteningComponentØ  Value(daNm)
-BoltCAMSHAFT SUPPORTSM71.5
1. Fit the exhaust side camshaft front oil seal (1a) using the tool (1b).
DescriptionCode
1bFitting tool1.860.824.000
1. Fit the inlet side camshaft front oil seal (1a) using the tool (1b).
DescriptionCode
1bFitting tool1.860.844.000
Position the cam angle sensor and secure it using the bolt.Position the exhaust side driven toothed pulley and secure it without tightening the bolts.Position the inlet side driven toothed pulley and secure it without tightening the bolts.    Op. 1032B14 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT VERSIONS WITH AIR CONDITIONER    Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R    Op. 1008A46 POWER UNIT RIGID SUPPORT - TIMING SIDE - R.R.    Op. 1016A20 SINGLE TAPPET COVER -R.R AND REPLACE GASKET    Op. 5510C14 IGNITION COIL/S - R+R    Op. 1088B10 ENGINE COOLANT SUPPLY RESERVOIR - R.R.    7055B42 PASSARUOTA supplementare ANTERIORE (uno), sx o dx - S.R.    Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.    4450B10 RUOTA (una) anteriore - S.R.    Op. 1048A23 COLD AIR INTAKE FOR AIR FILTER - R.R    1048A32 MANICOTTO da filtro aria a collettore aspirazione - S.R.    1048A28 DISPOSITIVO RISUONATORE circuito aria in depressione - S.R.Connect the negative battery terminal.    Op. 5530B56 BATTERY DRIP TRAY COVER - R.R.    1016A40 COPERCHIO BOBINE accensione su testa cilindri - S.R.Remove the vehicle from the lift.