1036C10 CAMSHAFTS IN CAMSHAFT HOUSING - R.R - INCLUDES CAMSHAFT HOUSING REPLACEMENT, IF NECESSARY - Fiat - STILO - eLearn

3362589 - 1036C10 CAMSHAFTS IN CAMSHAFT HOUSING - R.R - INCLUDES CAMSHAFT HOUSING REPLACEMENT, IF NECESSARY

) Op. 5530B56 BATTERY DRIP TRAY COVER - R.R.Make sure that the ignition key is in the OFF position, then disconnect the negative battery terminal. Op. 4450B04 RIGHT FRONT WHEEL - R.R Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R. 7055B42 PASSARUOTA supplementare ANTERIORE (uno), sx o dx - S.R. 1016A40 COPERCHIO BOBINE accensione su testa cilindri - S.R.. 1092D10 CINGHIA comando compressore condizionatore aria - S.R. 1092B68 CINGHIA da compressore condizionatore a comando alternatore - S.R. Op. 1032B10 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT1. Undo the exhaust side driven timing pulley bolt (1a) using the tools (1b) for counter-torque.

	Description	Code
1b	Support for counter-torque	1.860.831.000

	Description	Code
1b	Spanner for rotating timing pullies	1.860.831.002

2. Remove the exhaust side timing driven pulley.3. Undo the inlet side timing driven pulley bolts (3a) using the tool (3b) for counter-torque.

	Description	Code
3b	Counter-torque	1.860.856.000

4. Remove the inlet side timing driven pulley.

1. Disconnect the recirculation pipe (1b) from the connector (1a).2. Undo the retaining bolts.3. Move the engine coolant reservoir to the side.

Undo the bolts fixing the cam angle sensor to the camshaft front cap.1. Undo the bolts (1a) and remove the camshaft caps (1b).2. Remove the inlet side camshaft front supper upper half-bearing.3. Remove the camshafts.4. Remove the camshaft front oil seals.5. Remove the inlet side camshaft front support lower half-bearing.

Refitting ( Removing

) Place the inlet side camshaft front support lower half-bearing in its housing.Place the camshafts in their housings.Place the inlet side camshaft front upper upper half-bearing in its housing.Place the camshaft caps in their housings and secure them tightening the bolts to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	Camshaft caps	M7	1.5

1. Fit the exhaust side camshaft front oil seal (1a) using the tool (1b).

	Description	Code
1b	Fitting tool	1.860.824.000

1. Fit the inlet side camshaft front oil seal (1a) using the tool (1b).

	Description	Code
1b	Fitting tool	1.860.844.000

Tighten the bolts fixing the cam angle sensor to the camshaft front cap.Position the inlet side timing driven pulley and secure it without tightening the bolts.Position the exhaust side timing driven pulley and secure it without tightening the bolt.

The bolts securing the pullies are tightened when refitting the timing drive belt.

Op. 1032B10 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT 1092B68 CINGHIA da compressore condizionatore a comando alternatore - S.R. 1092D10 CINGHIA comando compressore condizionatore aria - S.R. 1016A40 COPERCHIO BOBINE accensione su testa cilindri - S.R.. 7055B42 PASSARUOTA supplementare ANTERIORE (uno), sx o dx - S.R. Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R. Op. 4450B04 RIGHT FRONT WHEEL - R.RConnect the negative battery terminal. Op. 1008A46 POWER UNIT RIGID SUPPORT - TIMING SIDE - R.R.