3360357 - Z56 UPSTREAM LAMBDA SENSOR SIGNAL ERROR

The diagnostic equipment signals the following error: Upstream Lambda signal

		Results of the tests
0	PRELIMINARY CHECKS	All OK	Problems met	Operation
	Connect the tester (Examiner or Examiner Plus) and transcribe the errors and environmental parametersCheck for the 'Upstream Lambda signal' error only	End of diagnosis	Only the 'Upstream Lambda signal', 'Mixture strength', 'Misfire', 'Catalyzer' and/or 'Downstream Lambda signal' errors are present	Continue to Step 1
			Only the 'Upstream Lambda signal', 'Mixture strength', 'Misfire', 'Catalyzer' and/or 'Downstream Lambda signal' errors are present	Identify and eliminate the cause of the anomaly.Continue to Step 8
1	ERROR DETAIL CHECK	All OK	Problems met	Operation
1.2 16v	Check the detail of the 'Upstream Lambda signal' errorIn particular, check that it is not 'Below minimum limit'	Continue to Step 3	The detail is 'Above upper limit' with error P0133, P0139 and/or P1133	See table   Z57
			The detail is 'Above upper limit' with error P0133, P0139 and/or P1133	See table   Z57
			The detail is 'Above upper limit' with error P0133, P0139 and/or P1133	Continue to Step 2
1.6 16v	Check the detail of the 'Upstream Lambda signal' errorIn particular, check that it is not 'Open circuit or short circuit to earth'	Continue to Step 3	The detail is 'Signal not plausible'	See table   Z57
			The detail is 'Open circuit or short circuit to earth'	Continue to Step 2
1.8 16v	Check the detail of the 'Upstream Lambda signal' errorIn particular, check that it is not 'Below minimum level'	Continue to Step 3	The detail is 'Above maximum limit' with error P0133 and/or P0153	See table   Z57
			The detail is 'Below minimum level'	Continue to Step 2
2.4 20v	Check the detail of the 'Upstream Lambda signal' errorIn particular check that it is not 'Signal not valid/Below minimum threshold'	Continue to Step 3	The detail is 'Above upper limit' with error P0133, P0153, P0139, P0159, P1133 and/or P1153	See table   Z57
			The detail is 'Below lower limit'	See table   Z57
			The detail is 'Signal not valid/Below minimum threshold'	Continue to Step 2
2	INTAKE AND EXHAUST SYSTEM LEAKAGE CHECK	All OK	Problems met	Operation
	Check the exhaust system visually and by listening. In particular, check that there are no leaks before the upstream Lambda sensor	Continue to Step 3	Leaks are present	Eliminate the leaks from the exhaust system, if necessary, replace the components involved
3	UPSTREAM LAMBDA SENSOR SWITCHING CHECK	All OK	Problems met	Operation
	Use a tester to cancel the errors in the control unit.Start the engine, let it warm up and check the activation of the 1st loop mixture strength check using the diagnostic equipment (or, alternatively, the switching of the upstream Lambda signal)	Continue to Step 4	The activation does not take place (or the signal does not switch)	Continue to Step 6
4	LAMBDA SENSOR WIRING CHECK	All OK	Problems met	Operation
	Check the upstream Lambda sensor wiring, checking that there are no false contacts See   E5030  PETROL ENGINE ELECTRONIC MANAGEMENT	Continue to Step 5	There are false contacts	Restore correct connections. If necessary, replace the defective componentsContinue to Step 8
5	ECU SOFTWARE CHECK	All OK	Problems met	Operation
	Using the FIAT documentation, check that the engine management software calibration is updated	Continue to Step 8	The control unit does not have updated software setting	Reprogramme the engine management control unit.Continue to Step 8
6	LAMBDA SENSOR/ECU INPUT WIRING CHECK	All OK	Problems met	Operation
	Check the wiring for the upstream Lambda sensor intake circuit in the ECU, checking that there are no short circuits to the supply or to earth, open circuits or false contacts See   E5030  PETROL ENGINE ELECTRONIC MANAGEMENT	Continue to Step 7	There are faulty connections	Restore correct connections. If necessary, replace the defective componentsContinue to Step 8
7	REPLACING UPSTREAM LAMBDA SENSOR	All OK	Problems met	Operation
	Replace the upstream Lambda sensor Op.   1080B60	Continue to Step 8
8	DELETING AND CHECKING ERROR	All OK	Problems met	Operation
	Use a tester to cancel the errors in the control unit.Carry out a road test and ensure the error does not recur	Continue to Step 9	The fault persists, it is the first time that this step has been reached and the Lambda sensor has not yet been replaced	Continue to Step 0
			The fault persists, but it is the second time that this step has been reached, or the Lambda sensor has already been replaced	Contact Technical Support for further information on the problem
9	CHECKING CORRECT OPERATION	All OK	Problems met	Operation
	Check that the fault is no longer present	End of diagnosis