1032B10 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT - Fiat - STILO - eLearn

3362425 - 1032b10 toothed timing belt - r + r for timing adjustment or replacement

) Place the car on a ramp. - 5530B56 BATTERY DRIP TRAY COVER - R.R. . Disconnect the battery negative terminal. - 1048A10 air cleaner filtering element - replace - 1056B60 single fuel manifold pipe, with injectors - r + r - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R. - 1092B60 alternator drive belt - r + r - 1092A10 Crankshaft services PULLEY - R.R. - 1032D12 timing system protective cover(s) - r + r - 1008B10 power unit front mount (timing side) flexible block - replace - 1008A46 cam shaft left rigid mount - r r1. Remove the protective plugs for the camshaft in the front and rear camshaft housings.2. Rotate the crankshaft in its normal direction of rotation and fit the tool in the splining in the camshaft.

	Name	Country
2	Locating pin	1.860.985.000

1. Check that the reference lug (1a), in the drive pulley, is opposite the engine rpm sensor (1b).

1. Loosen the nut fixing the moving tensioner (1a) and rmeove the timing belt (1b).

Refitting ( Removing

) 1. Remove the electrical connections for the spark plugs.2. Remove the spark plugs.3. Tighten the tool in the housing for the spark plugs for cylinders 1 and 2.

	Name	Country
3	Bearings	1.860.992.000

4. Rotate the crankshaft in its normal direction of rotation, using small movements, until the surface (4a) on the moving part of the tool is aligned with the fixed plane (4b) of the tool. When both tools positioned in the spark plug housings are in this condition, the pistons will be in line, i.e. halfway through their stoke and the piston for cylinder 1 will be descending, i.e. in the inlet stroke.

Rotate the crankshaft gradually to prevent the pin for the tools being expelled by the piston compression.

1. Use the tool (1a) and loosen the fixing bolt (1b) for the camshaft driven pulley.

	Name	Country
1a	Support for counter-torque	1.860.831.000

1. Raise the vehicle and fit the timing belt (1a) working in an anti-clockwise direction starting from the drive pulley (1b).

Use a suitable tool so that the moving tensioner is in the maximum tension position.Lower the lift and remove the tools used previously for timing and locking the camshaft and timing the crankshaft.

	Name	Country
-	Bearings	1.860.992.000

	Name	Country
-	Locating pin	1.860.985.000

1. Use the tool (1a) and tighten the bolt (1b) fixing the camshaft driven pulley to torque.

	Name	Country
1a	Support for counter-torque	1.860.831.000

	Fastening	Component	Ø	Value(daNm)
1b	Nut	TIMING GEAR DRIVEN PULLEYS	M12	12

Rotate the crankshaft through two revolutions in its normal direction of rotation.1. Loosen the nut (1a) fixing the moving tensioner and, using a suitable tool, act on the slot (1b) in the tensioner so that the moving reference (1c) coincides with the fixed reference (1d).

Rotate the crankshaft through two revolutions in its normal direction of rotation, the position the tools for aligning the pistons and timing the camshafts for a final check on the engine timing.

	Name	Country
-	Locating pin	1.860.985.000

	Name	Country
-	Bearings	1.860.992.000

Tighten the spark plugs.

	Fastening	Component	Ø	Value(daNm)
-	Spark plug	SPARK PLUGS	M12 x 1.25	2.7

Lower the lift.Remove the tools and fit the spark plugs in the housings in the cylinder head.Connect the electrical connections for the spark plugs.Tighten the protective plugs for the camshaft in the front and rear camshaft housings.

	Fastening	Component	Ø	Value(daNm)
-	Plug	TAPERED PLUG	M20 x 1.5	(Camshaft housing front side) 4

	Fastening	Component	Ø	Value(daNm)
-	Plug	TAPERED PLUG	M14 x 1.5	(Camshaft housing rear side) 1.5

- 1008A46 cam shaft left rigid mount - r r - 1008B10 power unit front mount (timing side) flexible block - replace - 1032D12 timing system protective cover(s) - r + r - 1092A10 Crankshaft services PULLEY - R.R. - 1092B60 alternator drive belt - r + r - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R. - 1056B60 single fuel manifold pipe, with injectors - r + r - 1048A10 air cleaner filtering element - replaceConnect the battery negative terminal. - 5530B56 BATTERY DRIP TRAY COVER - R.R. . Remove the vehicle from the ramp.