5505C26 BONNET WIRING - R R - Fiat - STILO - eLearn

3363071 - 5505C26 bonnet wiring - r r

) - 5040A10 Air conditioning refrigerant CIRCUIT - Draining and Refilling Place the car on a lift. - 5530B56 BATTERY DRIP TRAY COVER - R.R.Disconnect the battery negative terminal. - 7045A10 l/h or r/h front seat (one) - r+r - 7040L33 ARMREST ON TUNNEL COVER WITH ODDMENTS POCKET - R.R. - 3380A46 handbrake lever protective boot - r r - 7040L37 gear lever plate - r r - 7040A65 passenger compartment box lock , one , r r - 7065C42 ashtray (one) r+r - 5010C32 air outlet on panel trim for rear seats - r r - 7040L70 TUNNEL COVER REAR TRIM - R.R. - 7040L20 tunnel trim - r r - 7040A45 facia rh side cover - r r - 7040A31 flap assembly - r r - 5570T80 car radio unit - r+r - 7040A25 central facia trim - r r- 5570T10 car radio support - r+r - includes contact repair and supply circuit check - 5540D15 BULB FOR FOG LIGHT - R.R. WITH LAMP REMOVED - 5550C14 hazard warning light switch - r+r - 5580C18 air bag module - r+r- 4110A16 steering wheel - r r for replacement or checks for versions with airbag and manual gearbox with hydraulic selection - 7040A26 steering column trim - r+r

Refitting ( Removing

) Check that the wiring is undamaged and that the individual conductors are firmly attached to the connections.If necessary, check the continuity.Connect each individual electrical connector to the sensor used previusly in order to facilitate the routing of the section of cable removed in its original position.Pull the end of the sensor and restore the routing of the electrical wiring.Carry out the same operation for all the electrical connectors in the engine compartment wiring.Position the rear electrical wiring, securing it using the new retaining bands.Disconnect each individual electrical connector from the sensor.1. Refit the soundproofing compartment and secure it with the relevant retaining clips.

Raise the lift.1. Secure the fuel and anti-evaporation pipes to the retaining bands.2. Refit the soundproofing bulkhead.

Lower the ramp.1. Connect the high and low pressure pipes (1a) to the expansion valve and tighten the fixing nuts (1a) and (1b).

Secure the high and low pressure pipes to the mounting bracket.Connect the electrical sensors of the front wheel ABS sensors.

	Name	Connector
-	Left. front wheel sensor for ABS	K70

	Name	Connector
-	Right. front wheel sensor for ABS	K71

1. Connect the Selespeed gearbox sensors junction.

	Name	Connector
1	"Selespeed gearbox sensors coupling"	D79

2. Connect the junction.

Connect the electrical connectors under the engine compartment junction unit.

	Name	Connector
1	Engine compartment junction unit	B1C

	Name	Connector
1	Engine compartment junction unit	B1D

	Name	Connector
1	Engine compartment junction unit	B1E

Connect the leads to the positive battery terminal and fix them using the nuts.Connect the electrical connector for the Air Bag first impact sensor and the front right lights cluster, and secure the section of wiring to the retaining clips.

	Name	Connector
-	Air-Bag front sensor	K39

	Name	Connector
-	Right headlamp	F11

Fit the expansion tank and secure it with its bolts.Working in the engine compartment, disconnect the windscreen wiper motor electrical connector.

	Name	Connector
-	Windscreen wiper motor	N15

Working in the area of the front left wheelarch, secure the electrical wiring to the retaining clips.Working in the area of the front right wheelarch, connect the electrical connector for the horn, bi-directional windscreen washer and headlamp washer pump, front right earth unit and linear sensor and secure the electrical wiring to the retaining clips.

	Name	Connector
-	Horn	P5

	Name	Connector
-	Windscreen/rear window pump motor	N22

	Name	Connector
-	Headlamp washer pump motor	N25

	Name	Connector
-	Right front earth	C11

	Name	Connector
-	Linear sensor for fans	K120

Refit the pipe carrier corrugated tube.Secure the heated jet wiring and the washer fluid pipe to the retaining clips.Connect the washer fluid pipes to the jets.Connect the heated washer jet electrical connectors.

	Name	Connector
-	Left windscreen washer defrosting resistance	O50

	Name	Connector
-	Right windscreen washer defrosting resistance	O51

- 3330C30 brake fluid reservoir - r + r and wash inside - 3340A12 A'B.S. system. - electronic and hydraulic CONTROL UNIT R.R. - 0010T64 brake and or clutch fluid check level and top up as necessary - 0010T65 hydraulic brake system bleed air - 5550C22 l/h or r/h side flasher (one) - r+r - 7025A22 soundproofing lining for bonnet lid - r+r- 7055A18 Windscreen base TRIM - R.R. - 5050B34 windscreen wiper arm/s complete with blade - r+r - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R.- 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. - 4450B12 front or rear wheels (two) - r+r - 1072D50 device (vis) with adjustable air ducts - r r - 1072B10 inlet manifold - r + r and replace seal . - 1056B14 throttle case - r + r . - 1040A31 fuel filler pipe - rigid section - r r - 1056B82 injection/ignition system e.c.u. (one) - r + r - 5530B52 Battery DRIP TRAY/SUPPORT - R.R.- 5530B10 battery - r+r - 1016A40 ignition coil cover on cylinder head- r+r - 7055B54 under-engine guard - r r- 7040L17 passenger compartment floor front carpet - r r Connect the electrical connectors of the components housed in the interior compartment.

	Name	Connector
-	Brake pedal switch	I30

	Name	Connector
-	.Left rear wheel sensor for ABS	K75

	Name	Connector
-	.Right rear wheel sensor for ABS	K76

	Name	Connector
-	Clutch pedal switch	I31

	Name	Connector
-	Accelerator pedal potentiometer	K55

	Name	Connector
-	Yawing sensor	K74

	Name	Connector
-	Front / rear coupling	D6