1092B91 WATER PUMP BALANCING SHAFT DRIVE CHAIN GEARS AND COMPONENTS R R - Fiat - CROMA - eLearn

194000417 - 1092B91 WATER PUMP BALANCING SHAFT DRIVE CHAIN GEARS AND COMPONENTS R R

) - Position the vehicle on a lift.- Make sure that the ignition key is in the OFF position, then disconnect the battery terminal (-).

	Description	Connector
-	Battery	See A001 BATTERY

Op. 4450B04 RIGHT FRONT WHEEL - R.R Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R. Op. 1032A12 TIMING SYSTEM DRIVE CHAIN - R.R1. Remove the timing drive pulley.

1. Unscrew the bolts (1a) and remove the water pump/balancer shaft drive chain hydraulic tensioner.

1. Undo the bolts (1a) and remove the chain tensioner pads (1b).2. Remove the water pump/balancing shafts drive chain.3. Remove the water pump/balancing shafts drive chain pulley.

1. Using a suitable tool for counter-torque, undo the water pump drive gear fixing bolts.2. Remove the water pump drive gear.

1. Fit the tool (1a) using the bolt (1b) for securing it (it is the bolt fixing the counter-balance shaft flange).

Tool	Description	Function	Validity
2000000600	Counter-torque	Loosen/tighten counter-balance shaft drive pullies fixing bolts	2.2

2. Undo the bolt (2a) and remove the inlet side counter-balance shaft drive pulley (2b).

This pulley has the words "INTAKE" and "GREEN" stamped on it so that it is correctly refitted.

- Carry out the same operations for the exhaust side counter-balance shaft drive pulley.

This pulley has the words "EXHAUST" and "WHITE" stamped on it so that it is correctly refitted.

Refitting ( Removing

) 1. Position the inlet side counter-balance shaft drive pulley (1a) in its housing and secure it tightening the bolt (1b) to the recommended torque.

Component	Fastening	dia	Value (daNm)	Validity
Counter-balance shaft drive pullies	Bolt	M10 x 1.5	(counter-balance shaft side) 2.0 + 30° + 15°	2.2

2. Remove the tool used for counter-torque.

Tool	Description	Function	Validity
2000000600	Counter-torque	Loosen/tighten counter-balance shaft drive pullies fixing bolts	2.2

- Tighten the bolt fixing the counter-balance shaft flange to the recommended torque.

Component	Fastening	dia	Value (daNm)	Validity
Counter balance shafts	Bolt	M6 x 1	(engine crankcase side) 0.9	2.2

- Carry out the same operations for the exhaust side counter-balance shaft drive pulley.

1. Place the water pump drive gear back in its housing.2. Using a suitable tool for counter-torque, tighten the bolts fixing the water pump drive gear to the recommended torque.

Component	Fastening	dia	Value (daNm)	Validity
Water pump drive pulley	Bolt	M6 x 1	(water pump side) 0.8	2.2

- Place the water pump/balancing shafts drive chain pulley in its housing.

Take care that the word "FRONT" stamped on the pulley is facing the operator.

1. Position the references on the individual pullies as illustrated in the diagram, then proceed with fitting the water pump/balancing shafts drive chain following the order given below:- inlet side balancing shaft- timing chain drive pulley- water pump drive gear- exhaust side balancing shaftfollowing the instructions given below.

The copper mesh (a) should be aligned with the arrow stamped on the inlet side balancing shaft drive pulley; the silver mesh (b) should be aligned with the reference stamped on the drive pulley; the silver mesh (c) should be aligned with the arrow stamped on the exhaust side balancing shaft drive pulley.

2. Place the chain tensioner pads (2a) in their housing and secure it by tightening the bolts (2b) to the recommended torque.

Component	Fastening	dia	Value (daNm)	Validity
Water pump/balancing shafts drive chain pad(s)	Bolt	M6 x 1	(engine crankcase side) 1.0	2.2

1. Fit a suitable pin (diameter 1.5 mm) to secure the counter-balance shafts and water pump drive chain tensioner.

Press the tensioner piston and turn to the right to fit the tool.

2. Refit the water pump/balancer shaft drive chain hydraulic tensioner (2a) and secure by tightening bolts (2b) to the specified torque.

Component	Fastening	dia	Value (daNm)	Validity
Water pump/balancing shafts drive chain hydraulic tensioner	Bolt	M6 x 1	(engine crankcase side) 1.0	2.2

- Remove the pin from the counter-balance shaft drive chain tensioner and water pump.

- Place the timing drive chain pulley in its housing.

Take care over the fitting position: the word "FRONT" stamped on the pulley should be facing the operator.

Op. 1032A12 TIMING SYSTEM DRIVE CHAIN - R.R Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R. Op. 4450B04 RIGHT FRONT WHEEL - R.R- Connect the negative battery terminal. Op. 0010T11 ENGINE OIL - CHECK LEVEL AND TOP UP, IF NECESSARY- Remove the vehicle from the lift.