194003978 - 5540CA HEADLAMP ALIGNMENT SENSOR CHECK

STEPCHECK TO BE PERFORMEDRESOLUTION IF THE CHECK IS NOT OK
1With the ignition ON, check for the presence at Pin 5 of the headlamp alignment corrector front potentiometer connector    See K001 HEADLAMP ALIGNMENT CORRECTOR FRONT POTENTIOMETER (CAF)of a voltage of 5 V.Move on to Step 5Move on to Step 2
2If faults are present, restore the continuity of the wiring between the Master headlamp (left side) and the front potentiometer    See E3080 HEADLAMP AGLINMENT CORRECTORThe test can be considered overMove on to Step 3
3With the key ON, check for the presence at Pin 1 of the Master headlamp    See F010 LEFT HEADLAMPof a voltage of 5 VReplace the master headlamp    Op. 5540B81 LEFT GAS DISCHARGE LIGHT CLUSTER - R.R.
4Check the fault disappears.The test can be considered overReplace the headlamp control unit    Op. 5540B42 CONTROL UNIT OF ONE GAS DISCHARGE LIGHT CLUSTER R R
5With the ignition ON, check for the presence at Pin 5 of the headlamp alignment corrector rear potentiometer connector    See K002 HEADLAMP ALIGNMENT CORRECTOR REAR POTENTIOMETER (CAF)of a voltage of 5 V.Move on to Step 8Move on to Step 6
6If faults are present, restore the continuity of the wiring between the Master headlamp (left side) and the rear potentiometer    See E3080 HEADLAMP AGLINMENT CORRECTORThe test can be considered overMove on to Step 7
7With the key ON, check for the presence at Pin 4 of the headlamp    See F010 LEFT HEADLAMPof a voltage of 5 V.Move on to Step 4Replace the master headlamp    Op. 5540B81 LEFT GAS DISCHARGE LIGHT CLUSTER - R.R.
8Check Pin 1 of the potentiometer connector    See K001 HEADLAMP ALIGNMENT CORRECTOR FRONT POTENTIOMETER (CAF)for the presence of a negative signal.Move on to Step 11Move on to Step 9
9If faults are present, restore the continuity of the wiring between the Master headlamp (left side) and the front potentiometer    See E3080 HEADLAMP AGLINMENT CORRECTORThe test can be considered overMove on to Step 10
10With the key ON, check for the presence at Pin 4 of the headlamp    See F010 LEFT HEADLAMPof an earth signal.Move on to Step 4Replace the master headlamp    Op. 5540B81 LEFT GAS DISCHARGE LIGHT CLUSTER - R.R.
11Check Pin 1 of the potentiometer connector    See K002 HEADLAMP ALIGNMENT CORRECTOR REAR POTENTIOMETER (CAF)for the presence of a negative signal.Move on to Step 14Move on to Step 12
12If faults are present, restore the continuity of the wiring between the Master headlamp (left side) and the rear potentiometer    See E3080 HEADLAMP AGLINMENT CORRECTORThe test can be considered overMove on to Step 13
13With the key ON, check for the presence at Pin 6 of the headlamp    See F010 LEFT HEADLAMPof an earth signal.Move on to Step 4Replace the master headlamp    Op. 5540B81 LEFT GAS DISCHARGE LIGHT CLUSTER - R.R.
14Turn the ignition key to the ON position.Disconnect the front sensor connecting rod.Connect a Voltmeter across Pin 2 of the headlamp 6-way connector    See F010 LEFT HEADLAMPand the earth.Check that the voltage varies from 0.5 to 4.5 when the sensor mobile axis is turned by hand.Move on to Step 16Move on to Step 15
15If faults are present, restore the continuity of the wiring between the Master headlamp (left side) and the front potentiometer    See E3080 HEADLAMP AGLINMENT CORRECTORThe test can be considered overReplace the sensor    Op. 5540C42 SENSOR FOR CORRECTING/ALIGNING GAS DISCHARGE LIGHTING UNITS ON FRONT SUSPENSION - R R
16Turn the ignition key to the ON position.Disconnect the rear sensor connecting rod.Connect a Voltmeter across Pin 5 of the headlamp 6-way connector    See F010 LEFT HEADLAMPand the earth.Check that the voltage varies from 0.5 to 4.5 when the sensor mobile axis is turned by hand.The test can be considered overMove on to Step 17
17If faults are present, restore the continuity of the wiring between the Master headlamp (left side) and the rear potentiometer    See E3080 HEADLAMP AGLINMENT CORRECTORReplace the sensor    Op. 5540C46 SENSOR FOR CORRECTING/ALIGNING GAS DISCHARGE LIGHTING UNITS ON REAR SUSPENSION - R R