194001005 - 7035B14 REAR WINDOW GLASS - R.R INCLUDES CLEANING HOUSING

Removing ( Refitting ) Disconnect the negative battery terminal.

	Description	Connector
	BATTERY	See A001 BATTERY

    Op. 7015A58 INTERNAL TAILGATE MOULDING (ONE) - R+R    Op. 7015A04 TAILGATE INTERIOR PANEL - R+R    Op. 7015A07 TAILGATE SIDE TRIM - R&R    Op. 5050C34 REAR WIPER ARM WITH BLADE - R+R1. Disconnect the heated rear windscreen electrical connections.

	Description	Connector
1	HEATED REAR WINDSCREEN	See P055 HEATED REAR WINDSCREEN

- Fit the suction pads to work safely.1. Apply a double layer of protective adhesive tape to the edges of the bodywork.2. Use the vibrating knife with an appropriate blade and cut the sealant (2a) along the edges of the rearscreen (2b) working from the inside of the vehicle. Take care when cutting over the rearscreen centering side pins (2c). - After having cut the bead of sealant, using the suction pads and with the assistance of a second mechanic, remove the rearscreen from the vehicle. Refitting ( Removing ) 1. Using suitable equipment, cut and level the bead of sealant in the windscreen housing leaving a thickness of between 0.25 and 1 mm, taking care not to scratch the paintwork. The thickness of the sealant remaining in the housing will act as a support for the new bonding.2. Thoroughly clean the windscreen housing using an air jet and degrease fully using heptane. When bonding, 60 minutes after the bead of sealant has been cut and levelled, the surface of the actual sealant must be treated using the special activating product and it is necessary to wait for 15 minutes before fitting the windscreen.3. Clean and degrease the seats for the glass mountings using heptane. Replace the window adhesive mountings in the rearscreen housing with new ones from the parts dept. - If necessary, retouch the paintwork.New rearscreen preparation:1. Degrease the serigraphed perimeter of the new rearscreen involved in the bonding using heptane.2. Apply the glass adhesion promoter (primer) (2b) to the serigraphed perimeter using the wick (2a) supplied in the Kit.

Wait for about 15 minutes before continuing with the next operation to allow the adhesion promoter (primer) thinner to evaporate.

- Remove the adhesive tape from the edges of the bodywork.- Carry out a test fitting and centre the rearscreen perfectly.- Using a spray gun apply a bead of sealant along the perimeter of the rearscreen as evenly as possible.

Component	Type	Description	Classification	Qty.	Validity
Rear windscreen glass	Windscreen sealant	Product n° 71711976	-	-

Start the operation from the centre of the bottom and continue without breaks along the entire perimeter of the glass.

- Place the rearscreen in the housing, with the assistance of a second mechanic, straight after applying the sealant and let it bed in.1. Position the belt (1a), as illustrated, and tension it so that even pressure is exerted on the entire rearscreen to ensure that the matching between the glass (1b), sealant (1c) and rearscreen housing (1d) is correct. - Before refitting the vehicle interior and exterior elements, check that there are no penetration points by carrying out a water leakage test.- Connect the rearscreen electrical connections.

	Description	Connector
	HEATED REAR WINDSCREEN	See P055 HEATED REAR WINDSCREEN

    Op. 7015A04 TAILGATE INTERIOR PANEL - R+R    Op. 7015A07 TAILGATE SIDE TRIM - R&R    Op. 7015A58 INTERNAL TAILGATE MOULDING (ONE) - R+R    Op. 5050C34 REAR WIPER ARM WITH BLADE - R+R- Connect the negative battery terminal.

	Description	Connector
	BATTERY	See A001 BATTERY

Do not move the vehicle for the time recommended by the supplier of the sealant.