194000427 - 1810A20 CLUTCH - R + R

Removing ( Refitting ) - Position the vehicle on a lift.- Make sure that the ignition key is in the OFF position, then disconnect the battery terminal (-).
DescriptionConnector
-Battery    See A001 BATTERY
    Op. 4450B12 FRONT WHEELS (TWO) - R+R    Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.    Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.    Op. 7055B90 LEFT FRONT WHEEL ARCH LINER - R.R.    Op. 1080B95 REAR LAMBDA SENSOR TO CATALYTIC CONVERTER - R.R    Op. 1076B18 RIGID SECTION OF EXHAUST PIPE BETWEEN CATALYTIC CONVERTER AND SILENCER - R + R    Op. 7055A43 CENTRE FRONT GRILLE - R.R.    Op. 4410D10 FRONT SUSPENSION FRAME - R+R    Op. 5520B10 STARTER MOTOR - R+R    Op. 2110A10 MANUAL GEARBOX AND DIFFERENTIAL - R + R1. Fit the flywheel lock.
ToolDescriptionFunctionValidity
1860846000Counter-torqueFlywheel lock
2. With the centering tool (2) fitted, undo the bolts (2b) and remove the clutch drip tray (2c).
ToolDescriptionFunctionValidity
1870447000CenteringRemoving-refitting clutch plate/drip tray1.9 JTD 8V1.9 JTD 16V
- Remove the clutch plate.
Refitting ( Removing ) 1. Place the clutch plate and the clutch tray (1a) in their housing using the tool (1b) for centering.
ToolDescriptionFunctionValidity
1870447000CenteringRemoving-refitting clutch plate/drip tray1.9 JTD 8V1.9 JTD 16V
2. Tighten the new bolts securing the clutch tray to the recommended torque.
ComponentFasteningdia  Value (daNm)Validity
Clutch drip trayBolt (pretreated to be replaced)M8(engine flywheel side) 2.3 - 2.81.9 JTD 16v1.9 JTD 8v
- Remove the clutch plate and clutch tray centering tool.
ToolDescriptionFunctionValidity
1870447000CenteringRemoving-refitting clutch plate/drip tray1.9 JTD 8V1.9 JTD 16V
3. Remove the flywheel lock.
ToolDescriptionFunctionValidity
1860846000Counter-torqueFlywheel lock
    Op. 2110A10 MANUAL GEARBOX AND DIFFERENTIAL - R + R    Op. 5520B10 STARTER MOTOR - R+R    Op. 4410D10 FRONT SUSPENSION FRAME - R+R    Op. 7055A43 CENTRE FRONT GRILLE - R.R.    Op. 1076B18 RIGID SECTION OF EXHAUST PIPE BETWEEN CATALYTIC CONVERTER AND SILENCER - R + R    Op. 1080B95 REAR LAMBDA SENSOR TO CATALYTIC CONVERTER - R.R    Op. 7055B90 LEFT FRONT WHEEL ARCH LINER - R.R.    Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.    Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.    Op. 4450B12 FRONT WHEELS (TWO) - R+R    Op. 0010T64 BRAKE AND/OR CLUTCH FLUID CHECK LEVEL AND TOP UP AS NECESSARY    Op. 0010T67 HYDRAULIC CLUTCH SYSTEM - BLEED AIR    Op. 0010T41 MANUAL GEARBOX OIL CHECK LEVEL AND TOP UP IF NECESSARY- Connect the negative battery terminal.- Remove the vehicle from the lift.